[RFCs/IDs] [Plain Text] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]
Versions: 00 01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22 23
24 25 26 RFC 4444
Internet Engineering Task Force Jeff Parker
INTERNET DRAFT Axiowave Networks
Expiration Date: Nov 2002 May 2002
Management Information Base for IS-IS
<draft-ietf-isis-wg-mib-08.txt>
1. Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet- Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice Copyright (C) The Internet Society (2000). All
Rights Reserved.
Jeff Parker - Expires Nov 2002 [Page 1]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
2. Abstract
This document describes a management information base for the IS-IS
Routing protocol, as described in ISO 10589 [2], when it is used to
construct routing tables for IP networks, as described in RFC 1195
[RFC1195].
This memo defines an experimental portion of the Management
Information Base (MIB) for use with network management protocols in
the Internet community.
This memo is based on an IETF draft by Chris Gunner [1]. This
version has been modified to include MIB-II syntax, to exclude
portions of the protocol that are not relevant to IP, such as the
ES-IS protocol, and to add management support for current practice.
3. Table of Contents
1. Status of this Memo.................................. 1
2. Abstract............................................. 2
3. Table of Contents.................................... 2
4. Overview............................................. 2
5. Definition of IS-IS MIB.............................. 5
6. Acknowledgments...................................... 76
7. Security Considerations.............................. 76
8. References........................................... 78
9. Authors' Address..................................... 80
10. Full Copyright Statement............................. 80
4. Overview
This document is provided to the IETF working group on IS-IS.
The IS-IS MIB includes of the following objects
System-wide Attributes
- isisSystem
This table contains information specific to a single instance of
the IS-IS protocol running on a router.
- isisManAreaAddr
Jeff Parker - Expires Nov 2002 [Page 2]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
This table includes area addresses manually configured which are
used to control the associations formed between Level 1
Intermediate Systems.
- isisAreaAddr
This table includes area addresses reported in relevant L1 LSPs.
- isisSysProtSupp
This table includes the manually configured list of protocols,
such as IP or CLNS, supported by the Intermediate System.
- isisSummAddr
This table holds summary addresses configured for each Level 2
instance of the IS-IS protocol running on a router.
Circuit-specific Attributes
- isisCirc
This table contains information specific to a broadcast or
point-to-point interface in the system.
- isisCircLevel
This table contains information specific to a one Level 1 or
Level 2 of an interface.
- isisPacketCount
This optional table contains information on the number of PDUs of
each type sent at a single level in a single direction.
Attributes associated with an Adjacency
- isisISAdj
This table contains information about adjacencies to routers
maintained by the protocol. Entries in this table cannot be
created by management action: they are established through the
Hello protocol.
Jeff Parker - Expires Nov 2002 [Page 3]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
- isisISAdjAreaAddr
This table contains the set of Area Addresses of neighboring
Intermediate Systems as reported in IIH PDUs.
- isisISAdjIPAddr
This table contains the set of IP Addresses of neighboring
Intermediate Systems as reported in received IIH PDUs.
- isisISAdjProtSupp
This table contains the set of protocols supported by neighboring
Intermediate Systems as reported in received IIH PDUs.
Attributes associated with configured addresses
- isisRA
The Reachable Address Table.
This table contains information about an address prefix manually
configured on the system or learned through another protocol.
- isisIPRA
The IP Reachable Address Table.
This table contains information about IP reachable address
manually configured on this system or learned from another
protocol.
Attributes associated with a Notification
- isisNotification
This table defines attributes that will be included when
reporting IS-IS notifications.
The SNMP Management Framework presently consists of five major
components:
An overall architecture, described in RFC 2571 [RFC2571].
Jeff Parker - Expires Nov 2002 [Page 4]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in STD 16,
RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212] and RFC 1215
[RFC1215]. The second version, called SMIv2, is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
Message protocols for transferring management information. The first
version of the SNMP message protocol is called SNMPv1 and described
in STD 15, RFC 1157 [RFC1157]. A second version of the SNMP message
protocol, which is not an Internet standards track protocol, is
called SNMPv2c and described in RFC 1901 [RFC1901] and RFC 1906
[RFC1906]. The third version of the message protocol is called
SNMPv3 and described in RFC 1906 [RFC1906], RFC 2572 [RFC2572] and
RFC 2574 [RFC2574].
Protocol operations for accessing management information. The first
set of protocol operations and associated PDU formats is described in
STD 15, RFC 1157 [RFC1157]. A second set of protocol operations and
associated PDU formats is described in RFC 1905 [RFC1905].
A set of fundamental applications described in RFC 2573 [RFC2573] and
the view-based access control mechanism described in RFC 2575
[RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
5. Definition of IS-IS MIB
Jeff Parker - Expires Nov 2002 [Page 5]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
-- Changes in version 08.
-- Changed definiton of isisCircLevelDesIS to hold 7, not 6 bytes
-- Moved isisCircLocalID to CircLevel rather than IsisCircEntry
-- Remove isisCircIndex from isisIPRAEntry
-- Edit description of isisISAdjNeighPriority
-- Replace isisISAdjIPAddrAdjIndex with isisISAdjIndex
-- Simplified the names of variables which include Adj twice
-- isisISAdjAreaAddrAdjIndex, isisISAdjIPAddrAdjIndex,
-- and isisISAdjProtSuppAdjIndex.
-- Added isisSysMaxAge to control MaxAge for LSPs we generate
-- Added isisSysReceiveLSPBufferSize to control LSPs buffers
ISIS-MIB DEFINITIONS ::= BEGIN
IMPORTS
TEXTUAL-CONVENTION, DisplayString, RowStatus, TruthValue,
TestAndIncr
FROM SNMPv2-TC
MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, NOTIFICATION-TYPE,
Integer32, Counter32, experimental
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
InetAddressType, InetAddress, InetAddressPrefixLength
FROM INET-ADDRESS-MIB;
isisMIB MODULE-IDENTITY
LAST-UPDATED "200205061200Z" -- UTC date of the most recent REVISION.
ORGANIZATION "IETF IS-IS for IP Internets Working Group"
CONTACT-INFO
"Jeff Parker
Axiowave Networks
200 Nickerson Rd.
Marlborough, MA 01752
jparker@axiowave.com"
DESCRIPTION
"This document describes a management information base for
the IS-IS Routing protocol, as described in ISO 10589,
when it is used to construct routing tables for IP networks,
as described in RFC 1195.
This memo defines an experimental portion of the Management
Information Base (MIB) for use with network management
protocols in the Internet community.
This memo is based on a 1994 IETF draft by Chris Gunner.
Jeff Parker - Expires Nov 2002 [Page 6]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
This version has been modified to include MIB-II syntax, to
exclude portions of the protocol that are not relevant to IP,
and to add management support for current practice."
::= { experimental 37 }
-- Top-level stucture of the MIB
isisObjects OBJECT IDENTIFIER ::= { isisMIB 1 }
isisNotifications OBJECT IDENTIFIER ::= { isisMIB 2 }
isisConformance OBJECT IDENTIFIER ::= { isisMIB 3 }
-- OBJECT IDENTIFIER definitions
isisSystem OBJECT-IDENTITY
STATUS current
DESCRIPTION
"The object describes system wide attributes."
::= { isisObjects 1 }
isisCirc OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This object describes attributes associated with
one Circuit"
::= { isisObjects 2 }
isisCircLevelValues OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This object describes attributes associated with
area or domain relevant within a Circuit."
::= { isisObjects 3 }
isisCircPDUCounters OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This object collects counters associated with one Circuit
at one level."
::= { isisObjects 4 }
isisISAdj OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This object describes attributes associated with an
assoiciation with an adjacent Protocol Peer."
::= { isisObjects 5 }
Jeff Parker - Expires Nov 2002 [Page 7]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisReachAddr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This object describes attributes associated with
a configured address"
::= { isisObjects 6 }
isisIPReachAddr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This object describes attributes associated with
IP routes learned by configuration or through another
protocol."
::= { isisObjects 7 }
isisNotification OBJECT-IDENTITY
STATUS current
DESCRIPTION
"Objects included in Notifications."
::= { isisObjects 8 }
-- Type definitions
OSINSAddress ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"OSI Network Service Address, e.g. NSAP, SNPA, or Network
Entity Title"
SYNTAX OCTET STRING (SIZE(0..21))
SystemID ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A system ID."
SYNTAX OCTET STRING (SIZE(0..6))
LinkStatePDUID ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A Link State PDU Identifier."
SYNTAX OCTET STRING (SIZE(8))
AdminState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Type used in enabling and disabling a row."
SYNTAX INTEGER
Jeff Parker - Expires Nov 2002 [Page 8]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
{
off(1),
on(2)
}
UpTime ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Number of seconds since the object has entered the state 'up'.
If the object is not up, the number of seconds since the
circuit was up, or since the system started, if the circuit
has never been up."
SYNTAX Integer32
LSPBuffSize ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Integer sub range for LSP size."
SYNTAX Integer32 (512..16000)
LevelState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"states of the ISIS protocol."
SYNTAX INTEGER
{
off (1),
on (2),
waiting (3),
overloaded(4)
}
SupportedProtocol ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Types of network protocol supported by Integrated ISIS.
The values for ISO8473 and IP are those registered for
these protocols in ISO TR9577."
SYNTAX INTEGER
{
iso8473(129),
ip(204),
ipV6(205)
}
DefaultMetric ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
Jeff Parker - Expires Nov 2002 [Page 9]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
"Integer sub-range for default metric for single hop.
ISO 10589 provides for 4 types of metric. Only the
'default' metric is used in practice."
SYNTAX Integer32 (1..63)
MetricType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Is this an Internal or External Metric?"
SYNTAX INTEGER
{
internal(1),
external(2)
}
MetricStyle ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Do we use 1195 style Metrics or wide metrics."
SYNTAX INTEGER
{
narrow(1),
wide(2),
both(3)
}
ISLevel ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies a level."
SYNTAX INTEGER
{
area(1),
domain(2),
none(3)
}
IsisPDUHeader ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A block to contain the header from a PDU."
SYNTAX OCTET STRING (SIZE(1..64))
CircuitID ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"ID for a circuit."
SYNTAX OCTET STRING (SIZE(2..9))
Jeff Parker - Expires Nov 2002 [Page 10]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
ISPriority ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Integer sub-range for ISIS priority."
SYNTAX Integer32 (1..127)
-- Behavior Definitions
-- ResettingTimer behavior definition
-- "This object specifies the interval between certain events in
-- the operation of the protocol state machine. If the value of
-- this object is set to a new value while the protocol state
-- machine is in operation, the implementation shall take the
-- necessary steps to ensure that for any time interval which
-- was in progress when the value of the corresponding object
-- was changed, the next expiration of that interval takes place
-- the specified time after the original start of that interval,
-- or immediately, whichever is later. The precision with which
-- this time shall be implemented shall be the same as that
-- associated with the basic operation of the timer object."
-- ReplaceOnlyWhileDisabled behavior definition
-- "This object may not be modified while the corresponding
-- table row's variable of type AdminState is in state on."
-- OperationalState behavior definition
-- "This object controls the enabling and disabling of the
-- corresponding table row. Setting this object to the value
-- off has the effect of disabling the corresponding row.
-- Setting this object to the value on has the effect of
-- enabling the corresponding row. Setting the value of this
-- object to the same value as its current value has no effect.
-- If the table entry also contains an object controlling the
-- row status then the object following the operationalState
-- behavior shall not be set to on when the object following
-- the Row Status behavior has value off. An attempt to do
-- so is rejected."
isisSysTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisSysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The set of instance of the Integrated IS-IS
protocol existing on the system."
::= { isisSystem 1 }
isisSysEntry OBJECT-TYPE
Jeff Parker - Expires Nov 2002 [Page 11]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
SYNTAX IsisSysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row defines information specific to a single
instance of the IS-IS protocol existing on the system."
REFERENCE "{ISIS.poi cLNSISISBasic-P (1)}"
INDEX { isisSysInstance }
::= { isisSysTable 1 }
IsisSysEntry ::=
SEQUENCE {
isisSysInstance
Integer32,
isisSysVersion
DisplayString,
isisSysType
INTEGER,
isisSysID
SystemID,
isisSysMaxPathSplits
Integer32,
isisSysMaxLSPGenInt
Integer32,
isisSysOrigL1LSPBuffSize
LSPBuffSize,
isisSysMaxAreaAddresses
Integer32,
isisSysMinL1LSPGenInt
Integer32,
isisSysMinL2LSPGenInt
Integer32,
isisSysPollESHelloRate
Integer32,
isisSysWaitTime
Integer32,
isisSysAdminState
AdminState,
isisSysL1State
LevelState,
isisSysOrigL2LSPBuffSize
LSPBuffSize,
isisSysL2State
LevelState,
isisSysLogAdjacencyChanges
TruthValue,
isisSysMaxAreaCheck
TruthValue,
Jeff Parker - Expires Nov 2002 [Page 12]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisSysNextCircIndex
TestAndIncr,
isisSysExistState
RowStatus,
isisSysL2toL1Leaking
TruthValue,
isisSysSetOverload
INTEGER,
isisSysL1MetricStyle
MetricStyle,
isisSysL1SPFConsiders
MetricStyle,
isisSysL2MetricStyle
MetricStyle,
isisSysL2SPFConsiders
MetricStyle,
isisSysTEEnabled
ISLevel,
isisSysMaxAge
Integer32,
isisSysReceiveLSPBufferSize
Integer32
}
isisSysInstance OBJECT-TYPE
SYNTAX Integer32 (1..10000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The unique identifier of the Integrated IS-IS
instance to which this row corresponds.
This object follows the index behavior."
::= { isisSysEntry 1 }
isisSysVersion OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version number of the IS-IS protocol which this
instance implements."
REFERENCE "{ISIS.aoi version (1)}"
DEFVAL { "1" }
::= { isisSysEntry 2 }
isisSysType OBJECT-TYPE
SYNTAX INTEGER {
level1IS (1),
Jeff Parker - Expires Nov 2002 [Page 13]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
level2IS (2),
level1L2IS (3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of this instance of the Integrated
IS-IS protocol. This object follows the
replaceOnlyWhileDisabled behavior."
REFERENCE "{ISIS.aoi iSType (2)}"
DEFVAL { level1L2IS }
::= { isisSysEntry 3 }
isisSysID OBJECT-TYPE
SYNTAX SystemID
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The ID for this instance of the Integrated IS-IS
protocol. This value is appended to each of the
area addresses to form the Network Entity Titles.
The derivation of a value for this object is
implementation-specific. Some implementations may
automatically assign values and not permit an
SNMP write, while others may require the value
to be set manually."
REFERENCE "{ISIS.aoi systemId (119)}"
::= { isisSysEntry 4 }
isisSysMaxPathSplits OBJECT-TYPE
SYNTAX Integer32 (1..32)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum number of paths with equal routing metric value
which it is permitted to split between. This object
follows the replaceOnlyWhileDisabled behavior."
REFERENCE "{ISIS.aoi maximumPathSplits (3)}"
DEFVAL { 2 }
::= { isisSysEntry 5 }
isisSysMaxLSPGenInt OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum interval, in seconds, between generated LSPs
Jeff Parker - Expires Nov 2002 [Page 14]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
by this instance of the protocol. This object follows
the resettingTimer behavior.
Should be at least 300 seconds less than isisSysMaxAge."
REFERENCE "{ISIS.aoi maximumLSPGenerationInterval (6)}"
DEFVAL { 900 }
::= { isisSysEntry 6 }
isisSysOrigL1LSPBuffSize OBJECT-TYPE
SYNTAX LSPBuffSize
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum size of Level 1 LSPs and SNPs originated by
this instance of the protocol. This object follows the
replaceOnlyWhileDisabled behavior."
REFERENCE "{ISIS.aoi originatingL1LSPBufferSize (9)}"
DEFVAL { 1492 }
::= { isisSysEntry 7 }
isisSysMaxAreaAddresses OBJECT-TYPE
SYNTAX Integer32 (3..254)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of area addresses to be permitted for
this instance of the protocol. Note that all
Intermediate Systems in the same area must have the same
value configured for this attribute if correct operation
is to be assumed. This object follows the
replaceOnlyWhileDisabled behavior."
REFERENCE "{ISIS.aoi maximumAreaAddresses (4)}"
DEFVAL { 3 }
::= { isisSysEntry 8 }
isisSysMinL1LSPGenInt OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum interval, in seconds, between successive generation
of L1 LSPs with the same LSPID by this instace of the protocol.
This object follows the resettingTimer behavior."
REFERENCE "{ISIS.aoi minimumLSPGenerationInterval (11)}"
DEFVAL { 30 }
::= { isisSysEntry 9 }
isisSysMinL2LSPGenInt OBJECT-TYPE
Jeff Parker - Expires Nov 2002 [Page 15]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum interval, in seconds, between successive generation
of L2 LSPs with the same LSPID by this instance of the protocol.
This object follows the resettingTimer behavior."
REFERENCE "{ISIS.aoi minimumLSPGenerationInterval (11)}"
DEFVAL { 30 }
::= { isisSysEntry 10 }
isisSysPollESHelloRate OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value, in seconds, to be used for the suggested ES
configuration timer in ISH PDUs when soliciting the ES
configuration."
REFERENCE "{ISIS.aoi pollESHelloRate (13)}"
DEFVAL { 50 }
::= { isisSysEntry 11 }
isisSysWaitTime OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Number of seconds to delay in waiting state before
entering on state. This object follows the resettingTimer
behavior."
REFERENCE "{ISIS.aoi waitingTime (15)}"
DEFVAL { 60 }
::= { isisSysEntry 12 }
isisSysAdminState OBJECT-TYPE
SYNTAX AdminState
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The administrative state of this instance of the
Integrated IS-IS protocol. Setting this object to the
value 'on' when its current value is 'off' enables operation
of this instnace of the Integrated IS-IS protocol."
DEFVAL { off }
Jeff Parker - Expires Nov 2002 [Page 16]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
::= { isisSysEntry 13 }
isisSysL1State OBJECT-TYPE
SYNTAX LevelState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the Level 1 database.
The value 'overloaded' indicates a database that is
low on an essential resource, such as memory.
The administrator may set the state to 'wait' when
the router is initializing by setting the object
isisSysSetOverload.
If the state is waiting or overloaded, we
originate LSPs with the Overload bit set."
REFERENCE "{ISIS.aoi l1State (17)}"
::= { isisSysEntry 14 }
-- The following objects map those from the cLNSISISLevel2-P
-- Package
isisSysOrigL2LSPBuffSize OBJECT-TYPE
SYNTAX LSPBuffSize
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum size of Level 2 LSPs and SNPs originated by
this system. This object follows the
replaceOnlyWhileDisabled behavior."
REFERENCE "{ISIS.aoi originatingL2LSPBufferSize (26)}"
DEFVAL { 1492 }
::= { isisSysEntry 15 }
isisSysL2State OBJECT-TYPE
SYNTAX LevelState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the Level 2 database.
The value 'overloaded' indicates a database that is
low on an essential resource, such as memory.
The administrator may set the state to 'wait' when
the router is initializing by setting the object
isisSysSetOverload.
If the state is waiting or overloaded, we
originate LSPs with the Overload bit set."
REFERENCE "{ISIS.aoi l2State (28)}"
::= { isisSysEntry 16 }
Jeff Parker - Expires Nov 2002 [Page 17]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisSysLogAdjacencyChanges OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If true, causes IS-IS to generate a log message when an
IS-IS adjacency changes state (up or down)."
DEFVAL { false }
::= { isisSysEntry 17 }
isisSysMaxAreaCheck OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When on, enables checking of maximum area
addresses per IS version of ISO10589."
DEFVAL { true }
::= { isisSysEntry 18 }
isisSysNextCircIndex OBJECT-TYPE
SYNTAX TestAndIncr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to assign values to
isisCircIndex as described in 'Textual
Conventions for SNMPv2'. The network manager
reads this object, and then writes the value
back as the isisCircIndex in a SET that creates
a new instance of isisCircEntry. If the SET
fails with the code 'inconsistentValue', then
the process must be repeated; If the SET succeeds,
then the object is incremented, and the new
isisCircuit is created according to the manager's
directions."
::= { isisSysEntry 19 }
isisSysExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The state of the ISIS router. Turning this to
state 'destroy' forces the router to forget all
the current configuration. Setting the state to
'notInService' stops protocol processing, but
retains the configuration."
Jeff Parker - Expires Nov 2002 [Page 18]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
DEFVAL { active }
::= { isisSysEntry 20 }
isisSysL2toL1Leaking OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If true, allow the router to leak L2 routes into L1."
DEFVAL { false }
::= { isisSysEntry 21 }
isisSysSetOverload OBJECT-TYPE
SYNTAX INTEGER
{
setL1Overload(1),
setL2Overload(2),
setL1L2Overload(3),
overloadClear(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Administratively set the overload bit for each level.
The overload bit will continue to be set if the
implementation runs out of memory, independent of
this variable"
DEFVAL {overloadClear }
::= { isisSysEntry 22 }
isisSysL1MetricStyle OBJECT-TYPE
SYNTAX MetricStyle
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Which style of Metric do we generate in our L1 LSPs?
This object follows the replaceOnlyWhileDisabled
behavior."
DEFVAL { narrow }
::= { isisSysEntry 23 }
isisSysL1SPFConsiders OBJECT-TYPE
SYNTAX MetricStyle
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Which style of Metric do we consider in our
L1 SPF computation?"
Jeff Parker - Expires Nov 2002 [Page 19]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
DEFVAL { narrow }
::= { isisSysEntry 24 }
isisSysL2MetricStyle OBJECT-TYPE
SYNTAX MetricStyle
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Which style of Metric do we generate in our L2 LSPs?
This object follows the replaceOnlyWhileDisabled
behavior."
DEFVAL { narrow }
::= { isisSysEntry 25 }
isisSysL2SPFConsiders OBJECT-TYPE
SYNTAX MetricStyle
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Which style of Metric do we consider in our
SPF computation?"
DEFVAL { narrow }
::= { isisSysEntry 26 }
isisSysTEEnabled OBJECT-TYPE
SYNTAX ISLevel
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Do we do Traffic Engineering? At which level?"
DEFVAL { none }
::= { isisSysEntry 27 }
isisSysMaxAge OBJECT-TYPE
SYNTAX Integer32 (1200..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Value to place in RemainingLifeTime field of
the LSPs we generate.
This is should be at least 300 seconds greater than
isisSysMaxLSPGenInt."
DEFVAL { 1200 }
::= { isisSysEntry 28 }
isisSysReceiveLSPBufferSize OBJECT-TYPE
SYNTAX Integer32 (1492..65535)
Jeff Parker - Expires Nov 2002 [Page 20]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Size of the largest Buffer we can store.
This should be at least as big as the maximum
of isisSysOrigL2LSPBuffSize and isisSysOrigL1LSPBuffSize."
DEFVAL { 1492 }
::= { isisSysEntry 29 }
---
-- The Level 1 Manual Area Address Table
-- contains the set of area addresses manually configured
-- for each instance of the Integrated IS-IS protocol.
-- At least one row in which the value of isisManAreaAddrExistState
-- is active must be present for each active instance of
-- the protocol The maximum number of rows in this table for
-- each instance of the protocol for which the object
-- isisManAreaAddrExistState has the value active is the value
-- of isisSysMaxAreaAddresses.
-- An attempt to create more than isisSysMaxAreaAddresses
-- rows of isisManAreaAddrEntry with state 'active' in one
-- instance of the IS-IS protocol should return
-- inconsistentValue.
isisManAreaAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisManAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The set of manual area addresses configured on this
Intermediate System."
REFERENCE "{ISIS.aoi manualAreaAddresses (10)}"
::= { isisSystem 2 }
isisManAreaAddrEntry OBJECT-TYPE
SYNTAX IsisManAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one area address manually configured
on this system"
INDEX { isisSysInstance,
isisManAreaAddr }
::= { isisManAreaAddrTable 1 }
IsisManAreaAddrEntry ::=
SEQUENCE {
Jeff Parker - Expires Nov 2002 [Page 21]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisManAreaAddr
OSINSAddress,
isisManAreaAddrExistState
RowStatus
}
isisManAreaAddr OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A manually configured area address for this system. This
object follows the index behavior.
Note: an index for the entry {1, {49.0001} active} in
this table would be the ordered pair
(1, (0x03 0x49 0x00 0x01)), as the length of an Octet
string is part of the OID."
::= { isisManAreaAddrEntry 1 }
isisManAreaAddrExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The state of the isisManAreaAddrEntry. This object
follows the Row Status behavior. If the isisSysAdminState
for this instance of the IS-IS protocol is 'on', and an
attempt is made to set this object to the value 'destroy'
or 'notInService' when this is the only isisManAreaAddrEntry
in state 'active' for this instance of the IS-IS protocol
should return inconsistentValue."
DEFVAL { active }
::= { isisManAreaAddrEntry 2 }
-- The Level 1 Area Address Table
-- The Level 1 Area Address Table contains the
-- union of the sets of relevant area addresses reported
-- in all Level 1 LSPs received by this Intermediate System.
isisAreaAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Jeff Parker - Expires Nov 2002 [Page 22]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
"The union of the sets of area addresses reported in all
Level 1 LSPs with segment number zero received by this
instance of the protocol from Intermediate Systems which
are reachable via Level 1 routing."
REFERENCE "{ISIS.aoi areaAddresses (18)}"
::= { isisSystem 3 }
isisAreaAddrEntry OBJECT-TYPE
SYNTAX IsisAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one area address reported in a
Level 1 LSP received by this instance of the IS-IS
protocol."
INDEX { isisSysInstance,
isisAreaAddr }
::= { isisAreaAddrTable 1 }
IsisAreaAddrEntry ::=
SEQUENCE {
isisAreaAddr
OSINSAddress
}
isisAreaAddr OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An area address reported in a Level 1 LSP received by
this instance of the IS-IS protocol."
::= { isisAreaAddrEntry 1 }
-- The System Integrated Group
-- The System Integrated Group is present if the system
-- supports Integrated ISIS at Level 1.
-- The System Protocol Supported Table
-- The System Protocol Supported Table contains the manually
-- configured set of protocols supported by each
-- instance of the Integrated ISIS protocol.
--
isisSysProtSuppTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisSysProtSuppEntry
Jeff Parker - Expires Nov 2002 [Page 23]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the manually configured set of
protocols supported by each instance of the Integrated
ISIS protocol."
::= { isisSystem 4 }
isisSysProtSuppEntry OBJECT-TYPE
SYNTAX IsisSysProtSuppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one protocol supported by an
instance of the Integrated ISIS protocol."
INDEX { isisSysInstance,
isisSysProtSuppProtocol }
::= { isisSysProtSuppTable 1 }
IsisSysProtSuppEntry ::=
SEQUENCE {
isisSysProtSuppProtocol
SupportedProtocol,
isisSysProtSuppExistState
RowStatus
}
isisSysProtSuppProtocol OBJECT-TYPE
SYNTAX SupportedProtocol
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"One supported protocol. This object follows the index
behavior."
::= { isisSysProtSuppEntry 1 }
isisSysProtSuppExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The state of the isisSysProtSuppEntry. This object
follows the RowStatus behavior."
DEFVAL { active }
::= { isisSysProtSuppEntry 2 }
Jeff Parker - Expires Nov 2002 [Page 24]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
-- The Summary Address Table
-- The Summary Address Table contains the set of summary
-- addresses manually configured for each instance of
-- IP Integrated ISIS on the system.
isisSummAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisSummAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The set of IP summary addresses to use in forming
summary TLVs originated by this Intermediate System.
An administrator may use a summary address to combine
and modify IP Reachability announcements. If the
Intermediate system can reach any subset of the summary
address, the summary address will be announced instead,
at the configured metric."
::= { isisSystem 5 }
isisSummAddrEntry OBJECT-TYPE
SYNTAX IsisSummAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one IP summary address."
INDEX { isisSysInstance,
isisSummAddressType,
isisSummAddress,
isisSummAddrPrefixLen }
::= { isisSummAddrTable 1 }
IsisSummAddrEntry ::=
SEQUENCE {
isisSummAddressType
InetAddressType,
isisSummAddress
InetAddress,
isisSummAddrPrefixLen
InetAddressPrefixLength,
isisSummAddrExistState
RowStatus,
isisSummAddrAdminState
INTEGER,
isisSummAddrMetric
DefaultMetric
Jeff Parker - Expires Nov 2002 [Page 25]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
}
isisSummAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Type of IP address for this summary address.
This object follows the index behavior."
::= { isisSummAddrEntry 1 }
isisSummAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP Address value for this summary address.
This object follows the index behavior."
::= { isisSummAddrEntry 2 }
isisSummAddrPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength (0..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Length of the IP NetMask for this summary address."
::= { isisSummAddrEntry 3 }
isisSummAddrExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The existence state of this summary address. This object
follows the row status behavior."
DEFVAL { active }
::= { isisSummAddrEntry 4 }
isisSummAddrAdminState OBJECT-TYPE
SYNTAX INTEGER
{
summaryL1(1),
summaryL2(2),
summaryL1L2(3),
summaryOff(4)
}
MAX-ACCESS read-create
STATUS current
Jeff Parker - Expires Nov 2002 [Page 26]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
DESCRIPTION
"The administrative state of this entry. When the
administrative state changes, if the new value would
cause the contents of LSPs originated by the system
to change, then those new LSPs must be generated and
sent as soon as is permitted by the ISIS protocol.
A summary entry may exist but be disable (summaryOff).
Or it may be used to generate reacability entries at
a single level, such as Level 2 (summaryL2)."
DEFVAL { summaryOff }
::= { isisSummAddrEntry 5 }
isisSummAddrMetric OBJECT-TYPE
SYNTAX DefaultMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The metric value to announce this summary
address with in LSPs generated by this system."
DEFVAL { 20 }
::= { isisSummAddrEntry 6 }
-- System Stats
isisSysStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisSysStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics about system events."
::= { isisSystem 6 }
isisSysStatsEntry OBJECT-TYPE
SYNTAX IsisSysStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics about one level of the protocol."
INDEX { isisSysInstance,
isisSysStatLevel }
::= { isisSysStatsTable 1 }
IsisSysStatsEntry ::=
SEQUENCE {
isisSysStatLevel
Jeff Parker - Expires Nov 2002 [Page 27]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
INTEGER,
isisSysStatCorrLSPs
Counter32,
isisSysStatAuthTypeFails
Counter32,
isisSysStatAuthFails
Counter32,
isisSysStatLSPDbaseOloads
Counter32,
isisSysStatManAddrDropFromAreas
Counter32,
isisSysStatAttmptToExMaxSeqNums
Counter32,
isisSysStatSeqNumSkips
Counter32,
isisSysStatOwnLSPPurges
Counter32,
isisSysStatIDFieldLenMismatches
Counter32,
isisSysStatMaxAreaAddrMismatches
Counter32,
isisSysStatPartChanges
Counter32
}
isisSysStatLevel OBJECT-TYPE
SYNTAX INTEGER {
level1IS (1),
level2IS (2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The level that this entry describes."
::= { isisSysStatsEntry 1 }
isisSysStatCorrLSPs OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of corrupted in-memory LSPs detected.
LSPs received from the wire with a bad checksum
are silently dropped and not counted."
REFERENCE "{ISIS.aoi corruptedLSPsDetected (19)}"
::= { isisSysStatsEntry 2 }
Jeff Parker - Expires Nov 2002 [Page 28]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisSysStatAuthTypeFails OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of authentication type mismatches recognized
by this instance of the protocol."
::= { isisSysStatsEntry 3 }
isisSysStatAuthFails OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of authentication failures recognized by this
instance of the protocol."
::= { isisSysStatsEntry 4 }
isisSysStatLSPDbaseOloads OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the LSP L1 database has become
overloaded."
REFERENCE "{ISIS.aoi lSPL1DatabaseOverloads (20)}"
::= { isisSysStatsEntry 5 }
isisSysStatManAddrDropFromAreas OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a manual address has been dropped from
the area."
REFERENCE "{ISIS.aoi manualAddressesDroppedFromArea (21)}"
::= { isisSysStatsEntry 6 }
isisSysStatAttmptToExMaxSeqNums OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times the IS has attempted to exceed the
maximum sequence number."
REFERENCE "{ISIS.aoi
Jeff Parker - Expires Nov 2002 [Page 29]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
attemptsToExceedmaximumSequenceNumber (22)}"
::= { isisSysStatsEntry 7 }
isisSysStatSeqNumSkips OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a sequence number skip has occurred."
REFERENCE "{ISIS.aoi sequenceNumberSkips (23)}"
::= { isisSysStatsEntry 8 }
isisSysStatOwnLSPPurges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a zero-aged copy of the system's own LSP
is received from some other node."
REFERENCE "{ISIS.aoi ownLSPPurges (24)}"
::= { isisSysStatsEntry 9 }
isisSysStatIDFieldLenMismatches OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a PDU is received with a different value
for ID field length to that of the receiving system."
REFERENCE "{ISIS.aoi iDFieldLengthMismatches (25)}"
::= { isisSysStatsEntry 10 }
isisSysStatMaxAreaAddrMismatches OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a PDU is received with a different value
for MaximumAreaAddresses from that of the receiving
system."
REFERENCE "{ISIS.aoi MaximumAreaAddressesMismatches (118)}"
::= { isisSysStatsEntry 11 }
isisSysStatPartChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
Jeff Parker - Expires Nov 2002 [Page 30]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
STATUS current
DESCRIPTION
"partition changes"
::= { isisSysStatsEntry 12 }
-- The Circuit Group
-- The Circuit Group is current
-- The Circuit Table
-- Each broadcast or point-to-point interface on the system
-- corresponds to one entry in the Circuit table. There may be
-- many X.25 DA circuit entries in the Circuit table for an
-- X.25 interface.
isisCircTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisCircEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of circuits used by each instance of
Integrated IS-IS on this system."
::= { isisCirc 1 }
isisCircEntry OBJECT-TYPE
SYNTAX IsisCircEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An isisCircEntry exists for each circuit used by
Integrated IS-IS on this system."
INDEX { isisSysInstance,
isisCircIndex }
::= { isisCircTable 1 }
IsisCircEntry ::=
SEQUENCE {
isisCircIndex
Integer32,
isisCircIfIndex
Integer32,
isisCircIfSubIndex
Integer32,
isisCircLocalID
Integer32,
isisCircAdminState
AdminState,
isisCircExistState
Jeff Parker - Expires Nov 2002 [Page 31]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
RowStatus,
isisCircType
INTEGER,
isisCircExtDomain
TruthValue,
isisCircAdjChanges
Counter32,
isisCircInitFails
Counter32,
isisCircRejAdjs
Counter32,
isisCircOutCtrlPDUs
Counter32,
isisCircInCtrlPDUs
Counter32,
isisCircIDFieldLenMismatches
Counter32,
isisCircLevel
INTEGER,
isisCircMCAddr
INTEGER,
isisCircPtToPtCircID
CircuitID,
isisCircPassiveCircuit
TruthValue,
isisCircMeshGroupEnabled
INTEGER,
isisCircMeshGroup
Integer32,
isisCircSmallHellos
AdminState,
isisCircUpTime
UpTime
}
isisCircIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identifier of this circuit, unique within the
instance of the IS-IS protocol. This object follows
the index behavior. This is for SNMP Indexing
purposes only and need not have any relation to
any protocol value."
::= { isisCircEntry 1 }
isisCircIfIndex OBJECT-TYPE
Jeff Parker - Expires Nov 2002 [Page 32]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of ifIndex for the interface to which this
circuit corresponds. This object cannot be modified
after creation"
::= { isisCircEntry 2 }
isisCircIfSubIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A specifier for the part of the interface ifIndex to which
this circuit corresponds, such as a DLCI or VPI/VCI.
This object cannot be modified after creation"
::= { isisCircEntry 3 }
isisCircLocalID OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An identification that can be used in protocol packets
to identify a circuit. Values of isisCircLocalID do
not need to be unique. They are only required to differ
on LANs where the Intermediate System is the Designated
Intermediate System."
::= { isisCircEntry 4 }
isisCircAdminState OBJECT-TYPE
SYNTAX AdminState
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The administrative state of the circuit. This
object follows the AdminState behavior."
DEFVAL { off }
::= { isisCircEntry 5 }
isisCircExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The existence state of this circuit. This object follows
the Row Status behavior. Setting the state to 'notInService'
Jeff Parker - Expires Nov 2002 [Page 33]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
halts the generation and processing of IS-IS protocol PDUs
on this circuit. Setting the state to destroy will also
erase any configuration associated with the circuit."
DEFVAL { active }
::= { isisCircEntry 6 }
isisCircType OBJECT-TYPE
SYNTAX INTEGER {
broadcast(1),
ptToPt(2),
staticIn(3),
staticOut(4),
dA(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the circuit. This object follows the
replaceOnlyWhileDisabled behavior. The type specified
must be compatible with the type of the interface defined
by the value of isisCircIfIndex."
REFERENCE "{ISIS.aoi type (33)}"
::= { isisCircEntry 7 }
isisCircExtDomain OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If true, suppress normal transmission of and
interpretation of Intra-domain ISIS PDUs on this
circuit."
REFERENCE "{ISIS.aoi externalDomain (46)}"
DEFVAL { false }
::= { isisCircEntry 8 }
isisCircAdjChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an adjacency state change has
occurred on this circuit."
REFERENCE "{ISIS.aoi changesInAdjacencyState (40)}"
::= { isisCircEntry 9 }
isisCircInitFails OBJECT-TYPE
SYNTAX Counter32
Jeff Parker - Expires Nov 2002 [Page 34]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times initialization of this circuit has
failed."
REFERENCE "{ISIS.aoi initializationFailures (41)}"
::= { isisCircEntry 10 }
isisCircRejAdjs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an adjacency has been rejected on
this circuit."
REFERENCE "{ISIS.aoi rejectedAdjacencies (42)}"
::= { isisCircEntry 11 }
isisCircOutCtrlPDUs OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS control PDUs sent on this circuit."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { isisCircEntry 12 }
isisCircInCtrlPDUs OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS control PDUs received on this
circuit."
REFERENCE "{ISIS.aoi controlPDUsReceived (44)}"
::= { isisCircEntry 13 }
isisCircIDFieldLenMismatches OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times an IS-IS control PDU with an ID
field length different to that for this system has been
received."
Jeff Parker - Expires Nov 2002 [Page 35]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
REFERENCE "{ISIS.aoi iDFieldLengthMismatches (25)}"
::= { isisCircEntry 14 }
isisCircLevel OBJECT-TYPE
SYNTAX INTEGER
{
level1(1),
level2(2),
level1L2(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates which type of packets will be sent and
accepted on this circuit. The values used will be
modified by the settings of isisSysType. This
object follows the replaceOnlyWhileDisabled behavior."
DEFVAL { level1L2 }
::= { isisCircEntry 15 }
isisCircMCAddr OBJECT-TYPE
SYNTAX INTEGER{
group (1),
functional (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies which type of multicast address will
be used for sending HELLO PDUs on this
circuit. This may be used in Token Ring networks.
See section 8.4.8 of ISO 10589."
DEFVAL { group }
::= { isisCircEntry 16 }
isisCircPtToPtCircID OBJECT-TYPE
SYNTAX CircuitID
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ID of the circuit allocated during initialization.
If no value has been negotiated (either because the
adjacency is to an End System, or because initialization
has not yet successfully completed), this object has the
value which would be proposed for this circuit (i.e. the
concatenation of the local system ID and the one octet
local Circuit ID for this circuit."
REFERENCE "{ISIS.aoi ptPtCircuitID (51)}"
Jeff Parker - Expires Nov 2002 [Page 36]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
::= { isisCircEntry 17 }
isisCircPassiveCircuit OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Should we include this interface in LSPs, even if
it is not running the ISIS Protocol?"
REFERENCE "{}"
DEFVAL { false }
::= { isisCircEntry 18 }
isisCircMeshGroupEnabled OBJECT-TYPE
SYNTAX INTEGER {
inactive(1),
blocked(2),
set(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Is this port a member of a mesh group, or blocked?
Circuits in the same mesh group act as a virtual
multiaccess network. LSPs seen on one circuit in
a mesh group will not be flooded to another circuit
in the same mesh group."
REFERENCE "{}"
DEFVAL { inactive }
::= { isisCircEntry 19 }
isisCircMeshGroup OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Circuits in the same mesh group act as a virtual
multiaccess network. LSPs seen on one circuit in
a mesh group will not be flooded to another circuit
in the same mesh group. If isisCircMeshGroupEnabled
is inactive, this value is ignored."
REFERENCE "{}"
DEFVAL { 1 }
::= { isisCircEntry 20 }
isisCircSmallHellos OBJECT-TYPE
SYNTAX AdminState
MAX-ACCESS read-create
Jeff Parker - Expires Nov 2002 [Page 37]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
STATUS current
DESCRIPTION
"Can we send unpadded hellos on LAN circuits? Off means
LAN Hellos must be padded.
Implementations should allow the administrator to read
this value. An implementation need not be able to
support unpadded hellos to be conformant."
DEFVAL { off }
::= { isisCircEntry 21 }
isisCircUpTime OBJECT-TYPE
SYNTAX UpTime
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the circuit is up, the amount of time in seconds
since this circuit entered state 'up'. If the circuit
is not up, the number of seconds since the circuit was
up, or since the system started, if the circuit has
never been up.
Note: This can be implemented as start time less
the current time."
::= { isisCircEntry 22 }
-- The Circuit Level Table
-- This table captures level-specific information about a circuit
isisCircLevelTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisCircLevelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Level specific information about circuits used by IS-IS"
::= { isisCircLevelValues 1 }
isisCircLevelEntry OBJECT-TYPE
SYNTAX IsisCircLevelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An isisCircLevelEntry exists for each level on
each circuit used by Integrated IS-IS on this system."
INDEX { isisSysInstance,
isisCircIndex,
isisCircLevelIndex }
::= { isisCircLevelTable 1 }
Jeff Parker - Expires Nov 2002 [Page 38]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
IsisCircLevelEntry ::=
SEQUENCE {
isisCircLevelIndex
INTEGER,
isisCircLevelMetric
DefaultMetric,
isisCircLevelISPriority
ISPriority,
-- isisCircLevelCircID Removed: duplicates isisCircPtToPtCircID
-- CircuitID,
isisCircLevelDesIS
OCTET STRING,
isisCircLevelLANDesISChanges
Counter32,
isisCircLevelHelloMultiplier
Integer32,
isisCircLevelHelloTimer
Integer32,
isisCircLevelDRHelloTimer
Integer32,
isisCircLevelLSPThrottle
Integer32,
isisCircLevelMinLSPRetransInt
Integer32,
isisCircLevelCSNPInterval
Integer32,
isisCircLevelPartSNPInterval
Integer32
}
isisCircLevelIndex OBJECT-TYPE
SYNTAX INTEGER {
level1IS (1),
level2IS (2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The level that this entry describes."
::= { isisCircLevelEntry 1 }
isisCircLevelMetric OBJECT-TYPE
SYNTAX DefaultMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The metric value of this circuit for this level."
REFERENCE "{ISIS.aoi l1DefaultMetric (35)}"
Jeff Parker - Expires Nov 2002 [Page 39]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
DEFVAL { 10 }
::= { isisCircLevelEntry 2 }
isisCircLevelISPriority OBJECT-TYPE
SYNTAX ISPriority
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The priority for becoming LAN Designated
Intermediate System at this level."
REFERENCE "{ISIS.aoi l2IntermediateSystemPriority (73)}"
DEFVAL { 64 }
::= { isisCircLevelEntry 3 }
-- isisCircLevelCircID OBJECT-TYPE
-- SYNTAX CircuitID
-- MAX-ACCESS read-only
-- STATUS current
-- DESCRIPTION
-- "The ID of the circuit allocated during initialization.
-- If no value has been negotiated (either because the
-- adjacency is to an End System, or because initialization
-- has not yet successfully completed), this object has the
-- value which would be proposed for this circuit (i.e. the
-- concatenation of the local system ID and the one octet
-- local Circuit ID for this circuit."
-- REFERENCE "{ISIS.aoi ptPtCircuitID (51)}"
-- ::= { isisCircLevelEntry 4 }
isisCircLevelDesIS OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..7))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ID of the LAN Designated Intermediate System
on this circuit at this level. If, for any reason,
this system is not partaking in the relevant
Designated Intermediate System election process,
then the value returned is the zero length OCTET STRING."
REFERENCE "{ISIS.aoi l2DesignatedIntermediateSystem (75)}"
::= { isisCircLevelEntry 4 }
isisCircLevelLANDesISChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the LAN Designated
Jeff Parker - Expires Nov 2002 [Page 40]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
Intermediate System has changed at this level."
REFERENCE "{ISIS.aoi
lanL2DesignatedIntermediateSystemChanges (76)}"
::= { isisCircLevelEntry 5 }
isisCircLevelHelloMultiplier OBJECT-TYPE
SYNTAX Integer32 (2..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value is multiplied by the corresponding HelloTimer
and the result in seconds (rounded up) is used as the
holding time in transmitted hellos, to be used by receivers
of hello packets from this IS"
REFERENCE "{ISIS.aoi iSISHelloTimer (45)}"
DEFVAL { 10 }
::= { isisCircLevelEntry 6 }
isisCircLevelHelloTimer OBJECT-TYPE
SYNTAX Integer32 (10..600000)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum period, in milliseconds, between IIH PDUs
on multiaccess networks at this level for LANs.
The value at level 1 is used as the period between
Hellos on point to point circuits. Setting this
value at level 2 on a point to point circuit will
result in an error of InconsistentValue.
This object follows the resettingTimer behavior."
REFERENCE "{ISIS.aoi iSISHelloTimer (45)}"
DEFVAL { 3000 }
::= { isisCircLevelEntry 7 }
isisCircLevelDRHelloTimer OBJECT-TYPE
SYNTAX Integer32 (10..120000)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Period, in milliseconds, between Hello PDUs on
multiaccess networks when this IS is the Designated
Intermediate System. This object follows the
resettingTimer behavior."
REFERENCE "{ISIS.aoi iSISHelloTimer (45)}"
DEFVAL { 1000 }
Jeff Parker - Expires Nov 2002 [Page 41]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
::= { isisCircLevelEntry 8 }
isisCircLevelLSPThrottle OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimal interval of time, in milliseconds, between
transmissions of LSPs on an interface at this level."
REFERENCE "{ISIS.aoi minimumBroadcastLSPTransmissionInterval (5)}"
DEFVAL { 10 }
::= { isisCircLevelEntry 9 }
isisCircLevelMinLSPRetransInt OBJECT-TYPE
SYNTAX Integer32 (1..300)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum interval, in seconds, between re-transmission of
an LSP at this level. This object follows the resettingTimer
behavior.
Note that isisCircLevelLSPThrottle controls
how fast we send back to back LSPs. This variable
controls how fast we re-send the same LSP."
REFERENCE "{ISIS.aoi minimumLSPTransmissionInterval (5)}"
DEFVAL { 5 }
::= { isisCircLevelEntry 10 }
isisCircLevelCSNPInterval OBJECT-TYPE
SYNTAX Integer32 (1..600)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Interval of time, in seconds, between transmission
of CSNPs on multiaccess networks if this router is
the designated router at this level."
REFERENCE "{}"
DEFVAL { 10 }
::= { isisCircLevelEntry 11 }
isisCircLevelPartSNPInterval OBJECT-TYPE
SYNTAX Integer32 (1..120)
UNITS "seconds"
MAX-ACCESS read-create
Jeff Parker - Expires Nov 2002 [Page 42]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
STATUS current
DESCRIPTION
"Minimum interval in seconds between sending Partial Sequence
Number PDUs at this level. This object follows the
resettingTimer behavior."
REFERENCE "{ISIS.aoi partialSNPInterval (14)}"
DEFVAL { 2 }
::= { isisCircLevelEntry 12 }
-- isisPacketCountTable keeps track of the number of IS-IS
-- control packets sent and received at each level
isisPacketCountTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisPacketCountEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about IS-IS packets sent and received"
::= { isisCircPDUCounters 1 }
isisPacketCountEntry OBJECT-TYPE
SYNTAX IsisPacketCountEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about IS-IS protocol traffic at one level
on one circuit in one direction"
INDEX { isisSysInstance,
isisCircIndex,
isisPacketCountLevel,
isisPacketCountDirection }
::= { isisPacketCountTable 1 }
IsisPacketCountEntry ::=
SEQUENCE {
isisPacketCountLevel
INTEGER,
isisPacketCountDirection
INTEGER,
isisPacketCountHello
Counter32,
isisPacketCountLSP
Counter32,
isisPacketCountCSNP
Counter32,
isisPacketCountPSNP
Counter32
}
Jeff Parker - Expires Nov 2002 [Page 43]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisPacketCountLevel OBJECT-TYPE
SYNTAX INTEGER
{
level1(1),
level2(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The level at which these PDU counts have been collected."
::= { isisPacketCountEntry 1 }
isisPacketCountDirection OBJECT-TYPE
SYNTAX INTEGER
{
sending(1),
receiving(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Were we sending or receiving these PDUs?"
::= { isisPacketCountEntry 2 }
isisPacketCountHello OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS Hello PDUs seen in this
direction at this level."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { isisPacketCountEntry 3 }
isisPacketCountLSP OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS LSPs seen in this
direction at this level."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { isisPacketCountEntry 4 }
isisPacketCountCSNP OBJECT-TYPE
Jeff Parker - Expires Nov 2002 [Page 44]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS CSNPs seen in this
direction at this level."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { isisPacketCountEntry 5 }
isisPacketCountPSNP OBJECT-TYPE
SYNTAX Counter32
UNITS "frames"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IS-IS PSNPs seen in this
direction at this level."
REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}"
::= { isisPacketCountEntry 6 }
-- The Circuit IS Group
--
-- The Circuit IS Group is present if the system supports the
-- IS functions of the ISO 9542 protocol.
-- The Circuit IS Table
--
-- This table is not implemented - jdp
-- The IS Adjacency Group
--
-- The IS Adjacency Group is current and contains information
-- about adjacencies to routers maintained by the Integrated
-- IS-IS protocol
--
-- The IS Adjacency Table
--
-- Each adjacency to an IS corresponds to one entry in this
-- table.
isisISAdjTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisISAdjEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of adjacencies to Intermediate Systems."
Jeff Parker - Expires Nov 2002 [Page 45]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
::= { isisISAdj 1 }
isisISAdjEntry OBJECT-TYPE
SYNTAX IsisISAdjEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to one adjacency to an
Intermediate System on this system."
INDEX { isisSysInstance,
isisCircIndex,
isisISAdjIndex }
::= { isisISAdjTable 1 }
IsisISAdjEntry ::=
SEQUENCE {
isisISAdjIndex
Integer32,
isisISAdjState
INTEGER,
isisISAdjNeighSNPAAddress
OSINSAddress,
isisISAdjNeighSysType
INTEGER,
isisISAdjNeighSysID
OCTET STRING,
isisISAdjUsage
INTEGER,
isisISAdjHoldTimer
Integer32,
isisISAdjNeighPriority
ISPriority,
isisISAdjUpTime
UpTime
}
isisISAdjIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique value identifying the IS adjacency from all
other such adjacencies on this circuit. This value is
assigned by the system when the adjacency is created
automatically."
::= { isisISAdjEntry 1 }
isisISAdjState OBJECT-TYPE
Jeff Parker - Expires Nov 2002 [Page 46]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
SYNTAX INTEGER {
up (0),
initializing (1),
down (2),
failed (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the adjacency"
REFERENCE "{ISIS.aoi adjacencyState (78)}"
::= { isisISAdjEntry 2 }
isisISAdjNeighSNPAAddress OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNPA address of the neighboring system."
REFERENCE "{ISIS.aoi neighbourSNPAAddress (79)}"
::= { isisISAdjEntry 3 }
isisISAdjNeighSysType OBJECT-TYPE
SYNTAX INTEGER {
l1IntermediateSystem(1),
l2IntermediateSystem(2),
l1L2IntermediateSystem(3),
unknown(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the neighboring system."
REFERENCE "{ISIS.aoi neighbourSystemType (80)}"
::= { isisISAdjEntry 4 }
isisISAdjNeighSysID OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The system ID and 4 byte circuit ID of the
neighboring Intermediate System set from
the source ID field of the Three-Way-Handshake
information from the neighbor's IIH PDUs."
REFERENCE "{ISIS.aoi neighbourSystemIds (83)}"
::= { isisISAdjEntry 5 }
Jeff Parker - Expires Nov 2002 [Page 47]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisISAdjUsage OBJECT-TYPE
SYNTAX INTEGER {
level1(1),
level2(2),
level1and2(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An adjacency of type level1 is used for level 1
traffic only. An adjacency of type level2 is used
for level 2 traffic only. An adjacency of type level1and2
is used for both level 1 and level 2 traffic. There
may be two adjacencies (of types level1 and level2)
between the same pair of Intermediate Systems."
REFERENCE "{ISIS.aoi adjacencyUsage (82)}"
::= { isisISAdjEntry 6 }
isisISAdjHoldTimer OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The holding time in seconds for this adjacency.
This value is based on received IIH PDUs and
the elapsed time since receipt."
REFERENCE "{ISIS.aoi holdingTimer (85)}"
::= { isisISAdjEntry 7 }
isisISAdjNeighPriority OBJECT-TYPE
SYNTAX ISPriority
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Priority of the neighboring Intermediate System for
becoming the Designated Intermediate System."
REFERENCE "{ISIS.aoi lANPriority (86)}"
::= { isisISAdjEntry 8 }
isisISAdjUpTime OBJECT-TYPE
SYNTAX UpTime
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the adjacency is up, the amount of time in seconds
since this adjacency entered state 'up'. If the adjacency
Jeff Parker - Expires Nov 2002 [Page 48]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
is not up, the number of seconds since the adjacency was
up, or since the system started, if the adjacency has
never been up.
Note: This can be implemented as start time less
the current time."
::= { isisISAdjEntry 9 }
-- The IS Adjacency Area Address Table
-- The IS Adjacency Area Address Table contains the set of
-- Area Addresses of neighboring
-- Intermediate Systems as reported in IIH PDUs.
isisISAdjAreaAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisISAdjAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the set of Area Addresses of
neighboring Intermediate Systems as reported in received
IIH PDUs."
REFERENCE "{ISIS.aoi areaAddressesOfNeighbour (84)}"
::= { isisISAdj 2 }
isisISAdjAreaAddrEntry OBJECT-TYPE
SYNTAX IsisISAdjAreaAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one Area Address reported by a
neighboring Intermediate System in its IIH PDUs."
INDEX { isisSysInstance,
isisCircIndex,
isisISAdjIndex,
isisISAdjAreaAddrIndex,
isisISAdjAreaAddress }
::= { isisISAdjAreaAddrTable 1 }
IsisISAdjAreaAddrEntry ::=
SEQUENCE {
isisISAdjAreaAddrIndex
Integer32,
isisISAdjAreaAddress
OSINSAddress
}
isisISAdjAreaAddrIndex OBJECT-TYPE
Jeff Parker - Expires Nov 2002 [Page 49]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index for the areas associated with one neighbor.
This provides a simpler way to walk the table."
::= { isisISAdjAreaAddrEntry 1 }
isisISAdjAreaAddress OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"One Area Address as reported in IIH PDUs received from
the neighbor."
::= { isisISAdjAreaAddrEntry 2 }
-- The IS Adjacency IP Group
-- The IS Adjacency IP Group is present if the system supports
-- IP Integrated IS-IS
-- The IS Adjacency IP Address Table
-- The IS Adjacency IP Address Table contains the
-- set of IP Addresses of neighboring Intermediate Systems
-- as reported in received IIH PDUs.
isisISAdjIPAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisISAdjIPAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the set of IP Addresses of
neighboring Intermediate Systems as reported in received
IIH PDUs."
::= { isisISAdj 3 }
isisISAdjIPAddrEntry OBJECT-TYPE
SYNTAX IsisISAdjIPAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one IP Address reported by a
neighboring Intermediate System in its IIH PDUs."
INDEX { isisSysInstance,
isisCircIndex,
isisISAdjIndex,
Jeff Parker - Expires Nov 2002 [Page 50]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisISAdjIPAddrIndex
}
::= { isisISAdjIPAddrTable 1 }
IsisISAdjIPAddrEntry ::=
SEQUENCE {
isisISAdjIPAddrIndex
Integer32,
isisISAdjIPAddressType
InetAddressType,
isisISAdjIPAddress
InetAddress
}
isisISAdjIPAddrIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index to this table which identifies the IP addresss
to which this entry belongs."
::= { isisISAdjIPAddrEntry 1 }
isisISAdjIPAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of one IP Address as reported in IIH PDUs
received from the neighbor."
::= { isisISAdjIPAddrEntry 2 }
isisISAdjIPAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"One IP Address as reported in IIH PDUs received from the
neighbor."
::= { isisISAdjIPAddrEntry 3 }
-- The IS Adjacency Integrated Group
--
-- The IS Adjacency Integrated Group is present if the system
-- supports Integrated ISIS.
--
--
-- The IS Adjacency Protocol Supported Table
Jeff Parker - Expires Nov 2002 [Page 51]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
--
-- The IS Adjacency Protocol Supported Table contains the set of
-- protocols supported by neighboring
-- Intermediate Systems as reported in received IIH PDUs.
--
isisISAdjProtSuppTable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisISAdjProtSuppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the set of protocols supported by
neighboring Intermediate Systems as reported in received
IIH PDUs."
::= { isisISAdj 4 }
isisISAdjProtSuppEntry OBJECT-TYPE
SYNTAX IsisISAdjProtSuppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains one protocol supported by a
neighboring Intermediate System as reported in its IIH
PDUs."
INDEX { isisSysInstance,
isisCircIndex,
isisISAdjProtSuppIndex,
isisISAdjProtSuppProtocol }
::= { isisISAdjProtSuppTable 1 }
IsisISAdjProtSuppEntry ::=
SEQUENCE {
isisISAdjProtSuppIndex
Integer32,
isisISAdjProtSuppProtocol
SupportedProtocol
}
isisISAdjProtSuppIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identifier the IS adjacency to which this entry
corresponds."
::= { isisISAdjProtSuppEntry 1 }
isisISAdjProtSuppProtocol OBJECT-TYPE
SYNTAX SupportedProtocol
Jeff Parker - Expires Nov 2002 [Page 52]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"One supported protocol as reported in IIH PDUs received
from the neighbor."
::= { isisISAdjProtSuppEntry 2 }
--
--
-- The ES Adjacency Group
--
-- The ES Adjacency Group is present if the system supports
-- reception of ES Hellos
-- The ES Adjacency Table
--
-- This table is not implemented - jdp
--
--
-- The Reachable Address Group
--
-- The Reachable Address Group is optional.
-- The Reachable Address Table
-- Each entry records information about a reachable address
-- (NSAP or address prefix) manually configured on the system
-- or learned through another protocol.
isisRATable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisRAEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of Reachable Addresses to NSAPs or Address
Prefixes."
::= { isisReachAddr 1 }
isisRAEntry OBJECT-TYPE
SYNTAX IsisRAEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry defines a Reachable Address to a NSAP or
Address Prefix."
INDEX { isisSysInstance,
isisCircIndex,
isisRAIndex }
::= { isisRATable 1 }
IsisRAEntry ::=
SEQUENCE {
Jeff Parker - Expires Nov 2002 [Page 53]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisRAIndex
Integer32,
isisRAExistState
RowStatus,
isisRAAdminState
AdminState,
isisRAAddrPrefix
OSINSAddress,
isisRAMapType
INTEGER,
isisRAMetric
DefaultMetric,
isisRAMetricType
MetricType,
isisRASNPAAddress
OSINSAddress,
isisRASNPAMask
OSINSAddress,
isisRASNPAPrefix
OSINSAddress,
isisRAType
INTEGER
}
isisRAIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identifier for this isisRAEntry. This value must be
unique amongst all Reachable Addresses on the same parent
Circuit. This object follows the index and
manualOrAutomatic behaviors."
::= { isisRAEntry 1 }
isisRAExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The existence state of this Reachable Address. This
object follows the Row Status behaviors."
DEFVAL { active }
::= { isisRAEntry 2 }
isisRAAdminState OBJECT-TYPE
SYNTAX AdminState
MAX-ACCESS read-create
Jeff Parker - Expires Nov 2002 [Page 54]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
STATUS current
DESCRIPTION
"The administrative state of the Reachable Address. This
object follows the AdminState and manualOrAutomatic
behaviors."
DEFVAL { off }
::= { isisRAEntry 3 }
isisRAAddrPrefix OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The destination of this Reachable Address. This is an
Address Prefix. This object follows the
replaceOnlyWhileDisabled and manualOrAutomatic
behaviors."
REFERENCE "{ISIS.aoi addressPrefix (98)}"
::= { isisRAEntry 4 }
isisRAMapType OBJECT-TYPE
SYNTAX INTEGER {
none (1),
explicit (2),
extractIDI (3),
extractDSP (4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of mapping to be employed to ascertain the SNPA
Address which should be used in forwarding PDUs for this
Reachable Address prefix. This object follows the
manualOrAutomatic behavior. The following values of
mapping type are defined:
none: The mapping is null because the neighbor SNPA is
implicit by nature of the subnetwork (e.g. a
point-to-point linkage).
explicit: The subnetwork addresses in the object
isisRASNPAAddress is to be used.
extractIDI: The SNPA is embedded in the IDI of the
destination NSAP Address. The mapping algorithm
extracts the SNPA to be used according to the format
and encoding rules of ISO8473/Add2. This SNPA
extraction algorithm can be used in conjunction with
Reachable Address prefixes from the X.121, F.69, E.163
and E.164 addressing subdomains.
extractDSP: All, or a suffix, of the SNPA is embedded
Jeff Parker - Expires Nov 2002 [Page 55]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
in the DSP of the destination address. This SNPA
extraction algorithm extracts the embedded subnetwork
addressing information by performing a logical AND of
the isisRASNPAMask object value with the destination
address. The part of the SNPA extracted from the
destination NSAP is appended to the isisRASNPAPrefix
object value to form the next hop subnetwork
addressing information."
REFERENCE "{ISO10589-ISIS.aoi mappingType (107)}"
::= { isisRAEntry 5 }
isisRAMetric OBJECT-TYPE
SYNTAX DefaultMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The metric value for reaching the specified
prefix over this circuit. This object follows the
manualOrAutomatic behavior."
REFERENCE "{ISIS.aoi DefaultMetric (99)}"
DEFVAL { 20 }
::= { isisRAEntry 6 }
isisRAMetricType OBJECT-TYPE
SYNTAX MetricType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the metric is internal or
external. This object follows the manualOrAutomatic
behavior."
REFERENCE "{ISIS.aoi DefaultMetricType (103)}"
DEFVAL { internal }
::= { isisRAEntry 7 }
isisRASNPAAddress OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SNPA Address to which a PDU may be forwarded in
order to reach a destination which matches the address
prefix of the Reachable Address. This object follows the
manualOrAutomatic behavior."
REFERENCE "{ISIS.aoi sNPAAddresses (109)}"
-- note only one address may be specified per Reachable Address
-- in the MIB
DEFVAL { ''H }
Jeff Parker - Expires Nov 2002 [Page 56]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
::= { isisRAEntry 8 }
isisRASNPAMask OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A bit mask with 1 bits indicating the positions in the
effective destination address from which embedded SNPA
information is to be extracted. For the extraction the
first octet of the isisRASNPAMask object value is aligned
with the first octet (AFI) of the NSAP Address. If the
isisRASNPAMask object value and NSAP Address are of
different lengths, the shorter of the two is logically
padded with zeros before performing the extraction. This
object follows the manualOrAutomatic behavior."
REFERENCE "{ISIS.aoi sNPAMask (122)}"
DEFVAL { '00'H }
::= { isisRAEntry 9 }
isisRASNPAPrefix OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A fixed SNPA prefix for use when the isisRAMapType is
extractDSP. The SNPA Address to use is formed by
concatenating the fixed SNPA prefix with a variable SNPA
part that is extracted from the effective destination
address. For Reachable Address prefixes in which the
entire SNPA is embedded in the DSP the SNPA Prefix shall
be null. This object follows the manualOrAutomatic
behavior."
REFERENCE "{ISIS.aoi sNPAPrefix (123)}"
DEFVAL { '00'H }
::= { isisRAEntry 10 }
isisRAType OBJECT-TYPE
SYNTAX INTEGER
{
manual (1),
automatic (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" The type of Reachable address. Those of type
Jeff Parker - Expires Nov 2002 [Page 57]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
manual are created by the network manager. Those
of type automatic are created through propagation
of routing information from another routing
protocol (eg. IDRP). "
DEFVAL {manual}
::= {isisRAEntry 11 }
-- The IP Reachable Address Group
-- The IP Reachable Address Group is optional.
-- The IP Reachable Address Table
-- Each entry records information about one IP reachable
-- address manually configured on this system or learned from
-- another protocol.
isisIPRATable OBJECT-TYPE
SYNTAX SEQUENCE OF IsisIPRAEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of IP Reachable Addresses to networks,
subnetworks or hosts either manually configured or
learned from another protocol."
::= { isisIPReachAddr 1 }
isisIPRAEntry OBJECT-TYPE
SYNTAX IsisIPRAEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry defines an IP Reachable Address to a network,
subnetwork or host."
INDEX { isisSysInstance,
isisIPRAType,
isisIPRAIndex }
::= { isisIPRATable 1 }
IsisIPRAEntry ::=
SEQUENCE {
isisIPRAIndex
Integer32,
isisIPRAType
INTEGER,
isisIPRADestType
InetAddressType,
Jeff Parker - Expires Nov 2002 [Page 58]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
isisIPRADest
InetAddress,
isisIPRADestPrefixLen
InetAddressPrefixLength,
isisIPRAExistState
RowStatus,
isisIPRAAdminState
AdminState,
isisIPRAMetric
DefaultMetric,
isisIPRAMetricType
MetricType,
isisIPRASNPAAddress
OSINSAddress
}
isisIPRAIndex OBJECT-TYPE
SYNTAX Integer32 (1..2000000000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identifier for this isisIPRAEntry. This value must
be unique amongst all IP Reachable Addresses on the same
parent Circuit. This object follows the index and
manualOrAutomatic behaviors."
::= { isisIPRAEntry 1 }
isisIPRAType OBJECT-TYPE
SYNTAX INTEGER
{
manual (1),
automatic (2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of this IP Reachable Address. Those of type
manual are created by the network manager. Those of type
automatic are created through propagation of routing
information from another routing protocol."
::= { isisIPRAEntry 2 }
isisIPRADestType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of this IP Reachable Address."
Jeff Parker - Expires Nov 2002 [Page 59]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
::= { isisIPRAEntry 3 }
isisIPRADest OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The destination of this IP Reachable Address. This is
either a network address, subnetwork address or host
address. This object follows the manualOrAutomatic
behavior."
::= { isisIPRAEntry 4 }
isisIPRADestPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength (0..128)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The length of the IP Netmask for Reachability Address."
::= { isisIPRAEntry 5 }
isisIPRAExistState OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The state of this IP Reachable Address. This object
follows the ExistenceState and manualOrAutomatic
behaviors."
DEFVAL { active }
::= { isisIPRAEntry 6 }
isisIPRAAdminState OBJECT-TYPE
SYNTAX AdminState
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The administrative state of the IP Reachable Address. This
object follows the AdminState and manualOrAutomatic
behaviors."
DEFVAL { off }
::= { isisIPRAEntry 7 }
isisIPRAMetric OBJECT-TYPE
SYNTAX DefaultMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Jeff Parker - Expires Nov 2002 [Page 60]
Internet Draft - draft-ietf-isis-wg-mib-08.txt May 2002
"The metric value for reaching the specified
destination over this circuit. This object follows the
manualOrAutomatic behavior."
DEFVAL { 20 }
::= { isisIPRAEntry 8 }
isisIPRAMetricType OBJECT-TYPE
SYNTAX MetricType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the metric is internal or
external. This object follows the manualOrAutomatic
behavior."
DEFVAL { internal }
::= { isisIPRAEntry 9 }
isisIPRASNPAAddress OBJECT-TYPE
SYNTAX OSINSAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SNPA Address to which a PDU may be forwarded in
order to reach a destination which matches this IP
Reachable Address. This object follows the
manualOrAutomatic behavior."
DEFVAL { ''H }
::= { isisIPRAEntry 10 }
-- The Circuit CLNS Group
--
-- The Circuit CLNS Table contains objects controlling the
-- operation of the IS functions of the CLNS protocol
--
-- This table is not implemented - jdp
--
-- The IP Destination Group
-- The IP Destination Group is present if t