Skip to main content

T.140 Real-Time Text Conversation over WebRTC Data Channels
draft-ietf-mmusic-t140-usage-data-channel-14

The information below is for an old version of the document that is already published as an RFC.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 8865.
Authors Christer Holmberg , Gunnar Hellstrom
Last updated 2021-01-19 (Latest revision 2020-04-10)
Replaces draft-holmberg-mmusic-t140-usage-data-channel
RFC stream Internet Engineering Task Force (IETF)
Intended RFC status Proposed Standard
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state Submitted to IESG for Publication
Associated WG milestone
Mar 2020
Submit T.140 Real-time Text Conversation over WebRTC Data Channels as Proposed Standard
Document shepherd Flemming Andreasen
Shepherd write-up Show Last changed 2019-12-19
IESG IESG state Became RFC 8865 (Proposed Standard)
Action Holders
(None)
Consensus boilerplate Yes
Telechat date (None)
Responsible AD Murray Kucherawy
Send notices to Flemming Andreasen <fandreas@cisco.com>
IANA IANA review state Version Changed - Review Needed
IANA action state RFC-Ed-Ack
IANA expert review state Expert Reviews OK
draft-ietf-mmusic-t140-usage-data-channel-14
MMUSIC Working Group                                         C. Holmberg
Internet-Draft                                                  Ericsson
Updates: 8373 (if approved)                                 G. Hellstrom
Intended status: Standards TrackGunnar Hellstrom Accessible Communicatio
Expires: October 12, 2020                                 April 10, 2020

      T.140 Real-time Text Conversation over WebRTC Data Channels
              draft-ietf-mmusic-t140-usage-data-channel-14

Abstract

   This document specifies how a WebRTC data channel can be used as a
   transport mechanism for Real-time text using the ITU-T Protocol for
   multimedia application text conversation (Recommendation ITU-T
   T.140), and how the SDP offer/answer mechanism can be used to
   negotiate such data channel, referred to as T.140 data channel.  This
   document updates RFC 8373 to specify its use with WebRTC data
   channels.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on October 12, 2020.

Copyright Notice

   Copyright (c) 2020 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must

Holmberg & Hellstrom    Expires October 12, 2020                [Page 1]
Internet-Draft             T.140 Data Channel                 April 2020

   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Conventions . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  WebRTC Data Channel Considerations  . . . . . . . . . . . . .   4
   4.  SDP Considerations  . . . . . . . . . . . . . . . . . . . . .   4
     4.1.  Use of dcmap Attribute  . . . . . . . . . . . . . . . . .   4
     4.2.  Use of dcsa Attribute . . . . . . . . . . . . . . . . . .   5
       4.2.1.  Maximum Character Transmission Rate . . . . . . . . .   5
       4.2.2.  Real-time Text Conversation Languages . . . . . . . .   6
       4.2.3.  Real-time Text Direction  . . . . . . . . . . . . . .   7
     4.3.  Examples  . . . . . . . . . . . . . . . . . . . . . . . .   9
   5.  T.140 Considerations  . . . . . . . . . . . . . . . . . . . .  10
     5.1.  Session Layer Functions . . . . . . . . . . . . . . . . .  10
     5.2.  Data Encoding and Sending . . . . . . . . . . . . . . . .  11
     5.3.  Data Buffering  . . . . . . . . . . . . . . . . . . . . .  11
     5.4.  Loss of T140blocks  . . . . . . . . . . . . . . . . . . .  11
     5.5.  Multi-party Considerations  . . . . . . . . . . . . . . .  12
   6.  Gateway Considerations  . . . . . . . . . . . . . . . . . . .  12
   7.  Update to RFC 8373  . . . . . . . . . . . . . . . . . . . . .  13
   8.  Security Considerations . . . . . . . . . . . . . . . . . . .  14
   9.  IANA considerations . . . . . . . . . . . . . . . . . . . . .  14
     9.1.  Subprotocol Identifier t140 . . . . . . . . . . . . . . .  14
     9.2.  SDP fmtp Attribute  . . . . . . . . . . . . . . . . . . .  15
     9.3.  SDP Language Attributes . . . . . . . . . . . . . . . . .  15
     9.4.  SDP Media Direction Attributes  . . . . . . . . . . . . .  16
   10. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  17
   11. References  . . . . . . . . . . . . . . . . . . . . . . . . .  17
     11.1.  Normative References . . . . . . . . . . . . . . . . . .  17
     11.2.  Informative References . . . . . . . . . . . . . . . . .  19
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  19

1.  Introduction

   The ITU-T Protocol for multimedia application text conversation
   (Recommendation ITU-T T.140) [T140] defines a protocol for text
   conversation, also known as real-time text.  The transport used for
   IP networks is the "RTP Payload for Text Conversation" [RFC4103]
   mechanism, based on the Real-time Transport Protocol (RTP) [RFC3550].

   This document specifies how a WebRTC data channel
   [I-D.ietf-rtcweb-data-channel] can be used as a transport mechanism
   for T.140, and how the SDP offer/answer mechanism for data channels

Holmberg & Hellstrom    Expires October 12, 2020                [Page 2]
Internet-Draft             T.140 Data Channel                 April 2020

   [I-D.ietf-mmusic-data-channel-sdpneg] can be used to negotiate such a
   data channel.

   In this document, a T.140 data channel refers to a WebRTC data
   channel for which the instantiated sub-protocol is "t140", and where
   the channel is negotiated using the SDP-based external negotiation
   method [I-D.ietf-mmusic-data-channel-sdpneg].

   NOTE: The decision to transport real-time text using a WebRTC data
   channel, instead of using RTP based transport [RFC4103], is motivated
   by use-case "U-C 5: Real-time text chat during an audio and/or video
   call with an individual or with multiple people in a conference", see
   Section 3.2 of [I-D.ietf-rtcweb-data-channel].

   The brief notation "T.140" is used as a name for the text
   conversation protocol according to [T140].

   Real-time text is intended to be entered by human users from a
   keyboard, handwriting recognition, voice recognition or any other
   input method.  The rate of character entry is usually at a level of a
   few characters per second or less.

   Section 3 defines the generic data channel properties for a T.140
   data channel, and Section 4 defines how they are conveyed in an SDP
   dcmap attribute.  While this document defines how to establish a
   T.140 data channel using the SDP-based external negotiation method
   [I-D.ietf-mmusic-data-channel-sdpneg], the generic T.140 and gateway
   considerations defined in Section 3, Section 5 and Section 6 of this
   document can also be applied when a T.140 data channel is established
   using another mechanism (e.g., the mechanism defined in
   [I-D.ietf-rtcweb-data-protocol]).  Section 5 of
   [I-D.ietf-mmusic-data-channel-sdpneg] defines the mapping between the
   SDP dcmap attribute parameters and the protocol parameters used in
   [I-D.ietf-rtcweb-data-protocol].

   This document updates [RFC8373], by defining how the SDP hlang-send
   and hlang-recv attributes are used for the "application/webrtc-
   datachannel" media type.

2.  Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

Holmberg & Hellstrom    Expires October 12, 2020                [Page 3]
Internet-Draft             T.140 Data Channel                 April 2020

3.  WebRTC Data Channel Considerations

   The following WebRTC data channel property values
   [I-D.ietf-rtcweb-data-channel] apply to a T.140 data channel:

       +--------------------------+-------------------------------+
       | Subprotocol Identifier   | t140                          |
       | Transmission reliability | reliable                      |
       | Transmission order       | in-order                      |
       | Label                    | See Section 4.1 and Section 6 |
       +--------------------------+-------------------------------+

   NOTE: T.140 requires the transport channel to provide transmission of
   real-time text without duplication and in original order.  Therefore,
   T.140 does not specify reliable and ordered transmission of T.140
   data on the application layer.  Instead, when RTP based transport is
   used, the RTP sequence number is used to detect packet loss and out-
   of-order packets, and a redundancy mechanism is used to achieve
   reliable delivery of T.140 data.  By using the WebRTC data channel
   reliable and in-order transmission features
   [I-D.ietf-rtcweb-data-channel] for the T.140 data channel, there is
   no need for a redundancy mechanism or a mechanism to detect data loss
   and out-of-order delivery at the application level.  The latency
   characteristics of the T.140 data channel is also regarded to be
   sufficient to meet the application requirements of T.140.

4.  SDP Considerations

   The generic SDP considerations, including the SDP Offer/Answer
   procedures [RFC3264], for negotiating a WebRTC data channel are
   defined in [I-D.ietf-mmusic-data-channel-sdpneg].  This section, and
   its subsections, define the SDP considerations that are specific to a
   T.140 data channel, identified by an SDP 'dcmap' attribute
   [I-D.ietf-mmusic-data-channel-sdpneg]  with a "t140" attribute
   parameter value.

4.1.  Use of dcmap Attribute

   An offerer and answerer MUST, in each offer and answer, include an
   SDP 'dcmap' attribute [I-D.ietf-mmusic-data-channel-sdpneg] in the
   SDP media description (m= section) [I-D.ietf-mmusic-rfc4566bis]
   describing the SCTP association [RFC4960] used to realize the T.140
   data channel.

   The offerer and answerer MUST include the subprotocol attribute
   parameter, with a "t140" parameter value, in the 'dcmap' attribute
   value.

Holmberg & Hellstrom    Expires October 12, 2020                [Page 4]
Internet-Draft             T.140 Data Channel                 April 2020

   The offerer and answerer MAY include the priority attribute parameter
   and the label attribute parameter in the 'dcmap' attribute value, as
   specified in [I-D.ietf-mmusic-data-channel-sdpneg].

   NOTE: As specified in [I-D.ietf-rtcweb-data-channel], when a data
   channel is negotiated using the mechanism defined in
   [I-D.ietf-rtcweb-data-protocol], the label attribute parameter value
   has to be the same in both directions.  That rule also applies to
   data channels negotiated using the mechanism defined in this
   document.

   The offerer and answerer MUST NOT include the max-retr or the max-
   time attribute parameters in the 'dcmap' attribute.  If either of
   those attribute parameters is received in an offer, the answerer MUST
   reject the offer.  If either of those attribute parameters is
   received in an answer the offerer MUST NOT accept the answer.
   Instead, the answerer MUST take appropriate actions, e.g., by sending
   a new offer without a T.140 data channel, or by terminating the
   session.

   If the ordered attribute parameter is included in the 'dcmap'
   attribute, it MUST be assigned the value 'true'.

   Below is an example of the 'dcmap' attribute for a T.140 data channel
   with stream id=3 and without any label:

   a=dcmap:3 subprotocol="t140"

4.2.  Use of dcsa Attribute

   An offerer and answerer can, in each offer and answer, include one or
   more SDP 'dcsa' attributes [I-D.ietf-mmusic-data-channel-sdpneg] in
   the m= section describing the SCTP association used to realize the
   T.140 data channel.

   If an offerer or answerer receives a 'dcsa' attribute that contains
   an SDP attribute which usage has not been defined for a T.140 data
   channel, the offerer or answerer should ignore the 'dcsa' attribute,
   following the rules in Section 6.7 of
   [I-D.ietf-mmusic-data-channel-sdpneg].

4.2.1.  Maximum Character Transmission Rate

   A 'dcsa' attribute can contain the SDP 'fmtp' attribute used to
   indicate a maximum character transmission rate [RFC4103].  The 'cps'
   attribute parameter is used to indicate the maximum character
   transmission rate that the endpoint that includes the attribute is

Holmberg & Hellstrom    Expires October 12, 2020                [Page 5]
Internet-Draft             T.140 Data Channel                 April 2020

   able to receive, and the value is used as a mean value in characters
   per second over any 10-second interval.

   If the 'fmtp' attribute is included, the 'format' attribute parameter
   MUST be set to "t140".

   If no 'fmtp' attribute with a 'cps' attribute parameter is included,
   the default value of 30 applies [RFC4103].

   The offerer and answerer MAY modify the 'cps' attribute parameter
   value in subsequent offers and answers.

   This document does not define any other usage of the 'fmtp' attribute
   for a T.140 channel.  If an offerer or answerer receives a 'dcsa'
   attribute that contains an 'fmtp' attribute that is not according to
   the procedure above, the offerer or answerer MUST ignore the 'dcsa'
   attribute.

   NOTE: The 'cps' attribute parameter is especially useful when a T.140
   data channel endpoint is acting as a gateway (Section 6) and is
   interworking with a T.140 transport mechanism that have restrictions
   on how many characters can be sent per second.

   If an endpoint receives text at a higher rate than it can handle,
   e.g., because the sending endpoint does not support the 'cps'
   attribute parameter, it SHOULD either indicate to the sending
   endpoint that it is not willing to receive more text, using the
   direction attributes (Section 4.2.3), or use a flow control mechanism
   to reduce the rate.  However, in certain applications, e.g. emergency
   services, it is important to regain human interaction as soon as
   possible, and it might therefore be more appropriate to simply
   discard the received overflow, insert a mark for loss [T140ad1], and
   continue to process the received text as soon as possible.

   NOTE: At the time of writing this specification, the standardized API
   for WebRTC data channels does not support flow control.  Should such
   be available at some point, a receiving endpoint might use it in
   order to slow down the rate of text received from the sending
   endpoint.

4.2.2.  Real-time Text Conversation Languages

   'dcsa' attributes can contain the SDP 'hlang-send' and 'hlang-recv'
   attributes [RFC8373] to negotiate the language to be used for the
   real-time text conversation.

   For a T.140 data channel, the modality is "written" [RFC8373].

Holmberg & Hellstrom    Expires October 12, 2020                [Page 6]
Internet-Draft             T.140 Data Channel                 April 2020

4.2.3.  Real-time Text Direction

   'dcsa' attributes can contain the SDP 'sendonly', 'recvonly',
   'sendrecv' and 'inactive' attributes [I-D.ietf-mmusic-rfc4566bis] to
   negotiate the direction in which text can be transmitted in a real-
   time text conversation.

   NOTE: A WebRTC data channel is always bi-directional.  The usage of
   the 'dcsa' attribute only affects the direction in which
   implementations are allowed to transmit text on a T.140 data channel.

   The offer/answer rules for the direction attributes are based on the
   rules for unicast streams defined in [RFC3264], as described below.
   Note that the rules only apply to the direction attributes.

   Session-level direction attributes [I-D.ietf-mmusic-rfc4566bis] have
   no impact on a T.140 data channel.

4.2.3.1.  Generating an Offer

   If the offerer wishes to both send and receive text on a T.140 data
   channel, it SHOULD mark the data channel as sendrecv with a
   'sendrecv' attribute inside a 'dcsa' attribute.  If the offerer does
   not explicitly mark the data channel, an implicit 'sendrecv'
   attribute inside a 'dcsa' attribute is applied by default.

   If the offerer wishes to only send text on a T.140 data channel, it
   MUST mark the data channel as sendonly with a 'sendonly' attribute
   inside a 'dcsa' attribute.

   If the offerer wishes to only receive text on a T.140 data channel,
   it MUST mark the data channel as recvonly with a 'recvonly' attribute
   inside a 'dcsa' attribute.

   If the offerer wishes to neither send nor receive text on a T.140
   data channel, it MUST mark the data channel as inactive with an
   'inactive' attribute inside a 'dcsa' attribute.

   If the offerer has marked a data channel as sendrecv (or if the
   offerer did not explicitly mark the data channel) or recvonly, it
   MUST be prepared to receive T.140 data as soon as the state of the
   T.140 data channel allows it.

4.2.3.2.  Generating an Answer

   When the answerer accepts an offer, and marks the direction of the
   text in the corresponding answer, the direction is based on the
   marking (or the lack of explicit marking) in the offer.

Holmberg & Hellstrom    Expires October 12, 2020                [Page 7]
Internet-Draft             T.140 Data Channel                 April 2020

   If the offerer explicitly marked the data channel as sendrecv, or if
   the offerer did not mark the data channel, the answerer SHOULD mark
   the data channel as sendrecv, sendonly, recvonly or inactive with a
   'sendrecv', 'sendonly', 'recvonly' or 'inactive' attribute
   respectively inside a 'dcsa' attribute.  If the answerer does not
   explicitly mark the data channel, an implicit 'sendrecv' attribute
   inside a 'dcsa' attribute is applied by default.

   If the offerer marked the data channel as sendonly, the answerer MUST
   mark the data channel as recvonly or inactive with a 'recvonly' or
   'inactive' attribute respectively inside a 'dcsa' attribute.

   If the offerer marked the data channel as recvonly, the answerer MUST
   mark the data channel as sendonly or inactive with a 'sendonly' or
   'inactive' attribute respectively inside a 'dcsa' attribute.

   If the offerer marked the data channel as inactive, the answerer MUST
   mark the data channel as inactive with an 'inactive' attribute inside
   a 'dcsa' attribute.

   If the answerer has marked a data channel as sendrecv or recvonly, it
   MUST be prepared to receive data as soon as the state of the T.140
   data channel allows transmission of data.

4.2.3.3.  Offerer Receiving an Answer

   When the offerer receives an answer to the offer and the answerer has
   marked a data channel as sendrecv (or the answerer did not mark the
   data channel) or recvonly in the answer, the offerer can start
   sending T.140 data as soon as the state of the T.140 data channel
   allows it.  If the answerer has marked the data channel as inactive
   or sendonly, the offerer MUST NOT send any T.140 data.

   If the answerer has not marked the direction of a T.140 data channel
   in accordance with the procedures above, it is RECOMMENDED that the
   offerer does not process that as an error situation, but rather
   assume that the answerer might both send and receive T.140 data on
   the data channel.

4.2.3.4.  Modify Text Direction

   If an endpoint wishes to modify a previously negotiated text
   direction in an ongoing session, it MUST initiate an offer that
   indicates the new direction, following the rules in Section 4.2.3.1.
   If the answerer accepts the offer it follows the procedures in
   Section 4.2.3.2.

Holmberg & Hellstrom    Expires October 12, 2020                [Page 8]
Internet-Draft             T.140 Data Channel                 April 2020

4.3.  Examples

   Below is an example of an m= section of an offer for a T.140 data
   channel offering real-time text conversation in Spanish and
   Esperanto, and an m= section in the associated answer accepting
   Esperanto.  The maximum character transmission rate is set to 20.  As
   the offerer and answerer have not explicitly indicated the real-time
   text direction, the default direction "sendrecv" applies.

   Offer:

       m=application 911 UDP/DTLS/SCTP webrtc-datachannel
       c=IN IP6 2001:db8::3
       a=max-message-size:1000
       a=sctp-port 5000
       a=setup:actpass
       a=dcmap:2 label="ACME customer service";subprotocol="t140"
       a=dcsa:2 fmtp:t140 cps=20
       a=dcsa:2 hlang-send:es eo
       a=dcsa:2 hlang-recv:es eo

   Answer:

       m=application 2004 UDP/DTLS/SCTP webrtc-datachannel
       c=IN IP6 2001:db8::1
       a=max-message-size:1000
       a=sctp-port 6000
       a=setup:passive
       a=dcmap:2 label="ACME customer service";subprotocol="t140"
       a=dcsa:2 fmtp:t140 cps=20
       a=dcsa:2 hlang-send:eo
       a=dcsa:2 hlang-recv:eo

   Below is an example of an m= section of an offer for a T.140 data
   channel where the offerer wishes to only receive real-time text, and
   an m= section in the associated answer indicating that the answerer
   will only send real-time text.  No maximum character transmission
   rate is indicated.  No preference for the language to be used for the
   real-time text conversation is indicated.

Holmberg & Hellstrom    Expires October 12, 2020                [Page 9]
Internet-Draft             T.140 Data Channel                 April 2020

   Offer:

       m=application 1400 UDP/DTLS/SCTP webrtc-datachannel
       c=IN IP6 2001:db8::3
       a=max-message-size:1000
       a=sctp-port 5000
       a=setup:actpass
       a=dcmap:2 label="ACME customer service";subprotocol="t140"
       a=dcsa:2 recvonly

   Answer:

       m=application 2400 UDP/DTLS/SCTP webrtc-datachannel
       c=IN IP6 2001:db8::1
       a=max-message-size:1000
       a=sctp-port 6000
       a=setup:passive
       a=dcmap:2 label="ACME customer service";subprotocol="t140"
       a=dcsa:2 sendonly

5.  T.140 Considerations

5.1.  Session Layer Functions

   Section 6.1 of [T140] describes the generic T.140 session control
   functions at a high-level in a signalling protocol independent
   manner.  The list below describes how the functions are realized when
   using a T.140 data channel.

   o  Prepare session: An endpoint can indicate its support of T.140
      data channels using signalling specific means (e.g., using SIP
      OPTIONS [RFC3261]), or by indicating the support in an offer or
      answer (Section 4)
   o  Initiate session: An offer used to request the establishment of a
      T.140 data channel (Section 4)
   o  Accept session: An answer used to accept a request to establish a
      T.140 data channel (Section 4)
   o  Deny session: An answer used to reject a request to establish a
      T.140 data channel, using the generic procedures for rejecting a
      data channel [I-D.ietf-mmusic-data-channel-sdpneg]
   o  Disconnect session: An offer or answer used to disable a
      previously established T.140 data channel, using the generic
      procedures for closing a data channel
      [I-D.ietf-mmusic-data-channel-sdpneg]
   o  Data: Data sent on an established T.140 data channel (Section 5.2)

Holmberg & Hellstrom    Expires October 12, 2020               [Page 10]
Internet-Draft             T.140 Data Channel                 April 2020

5.2.  Data Encoding and Sending

   T.140 text is encoded and framed as T140blocks [RFC4103].

   Each T140block is sent on the SCTP stream [RFC4960] used to realize
   the T.140 data channel using standard T.140 transmission procedures
   [T140].  One or more T140blocks can be sent in a single SCTP user
   message [RFC4960].  Unlike RTP based transport for real-time text
   [RFC4103], T.140 data channels do not use redundant transmission of
   text.  The reason for this is that the T.140 data channel achieves
   robust transmission by using the "reliable" mode of the data channel.

   Data sending procedures conform to [T140].

   See Section 8 of [T140] for coding details.

   NOTE: The T.140 coding details contain information on optional
   control codes for controlling the presentation which may not be
   supported by the presentation level of the receiving application.
   The receiving application is expected to handle reception of such
   T.140 control codes appropriately (e.g. ignore and skip them) even if
   their effect on the presentation is not supported.

5.3.  Data Buffering

   As described in [T140], buffering can be used to reduce overhead,
   with the maximum assigned transmission interval of T140blocks from
   the buffer being 500 ms as long as there is text to send.

   Buffering MAY also be used for staying within the maximum character
   transmission rate (Section 4.2).

   An implementation needs to take the user requirements for smooth flow
   and low latency in real-time text conversation into consideration
   when assigning a transmission interval.  It is RECOMMENDED to use the
   default transmission interval of 300 milliseconds [RFC4103], for
   T.140 data channels.  Implementers might also use lower values for
   specific applications requiring low latency, taking the increased
   overhead in consideration.

5.4.  Loss of T140blocks

   In case of network failure or congestion, T.140 data channels might
   fail and get torn down.  If this happens but the session sustains, it
   is RECOMMENDED that implementations try to reestablish the T.140 data
   channels.  As a T.140 data channel does not provide a mechanism for
   the receiver to identify retransmitted T140blocks after channel
   reestablishment, the sending endpoint MUST NOT retransmit T140blocks.

Holmberg & Hellstrom    Expires October 12, 2020               [Page 11]
Internet-Draft             T.140 Data Channel                 April 2020

   Similarly, a receiver SHOULD indicate to the user that there has been
   a channel reestablishment, and that text might have been lost.  This
   MAY be done by inserting the missing text markers [T140ad1] or in any
   other way evident to the user.

   NOTE: If the SCTP association [RFC4960] used to realize the T.140
   data channel fails and gets torn down, it needs to be re-established
   before the T.140 data channel can be reestablished.  The procedures
   after the reestablishment of the T.140 data channel defined in this
   section apply no matter if only the T.140 data channel, or the whole
   SCTP association, got torn down.

5.5.  Multi-party Considerations

   If an implementation needs to support multi-party scenarios, the
   implementation needs to support multiple simultaneous T.140 data
   channels, one for each remote party.  At the time of writing this
   document, this is true even in scenarios where each participant
   communicates via a centralized conference server.  The reason is
   that, unlike RTP media, WebRTC data channels and the T.140 protocol
   do not support the indication of the source of T.140 data.  The SDP
   'dcmap' attribute label attribute parameter (Section 4.1) can be used
   by the offerer to provide additional information about each T.140
   data channel, and help implementations to distinguish between them.

   NOTE: Future extensions to T.140, or to the T140block, might allow
   indicating the source of T.140 data, in which case it might be
   possible to use a single T.140 data channel to transport data from
   multiple remote sources.  The usage of a single T.140 data channel,
   without any protocol extensions, would require the conference server
   to only forward real-time text from one source at any given time, and
   e.g., include human readable text labels in the real-time text stream
   that indicate the source whenever the conference server switches the
   source.  This would allow the receiver to present real-time text from
   different sources separately.  The procedures of such mechanism are
   outside the scope of this document.

6.  Gateway Considerations

   A number of real-time text transports and protocols have been defined
   for both packet-switched and circuit-switched networks.  Many are
   based on the ITU-T T.140 protocol on application and presentation
   level [T140].  At the time of writing this document, some mechanisms
   are no longer used, as the technologies they use have been obsoleted,
   while others are still in use.

   When performing interworking between T.140 data channels and real-
   time text in other transports and protocols, a number of factors need

Holmberg & Hellstrom    Expires October 12, 2020               [Page 12]
Internet-Draft             T.140 Data Channel                 April 2020

   to be considered.  At the time of writing this document, the most
   common IP-based real-time text transport is the RTP based mechanism
   defined in [RFC4103].  While this document does not define a complete
   interworking solution, this list below provides some guidance and
   considerations to take into account when designing a gateway for
   interworking between T.140 data channels and RTP-based T.140
   transport:

   o  For each T.140 data channel there is an RTP stream for real-time
      text [RFC4103].  Redundancy is by default declared and used on the
      RTP stream.  There is no redundancy on the T.140 data channel, but
      the reliable property [I-D.ietf-mmusic-data-channel-sdpneg] is set
      on it.
   o  During a normal text flow, T140blocks received from one network
      are forwarded towards the other network.  Keep-alive traffic is
      handled by lower layers on the T.140 data channel.  A gateway
      might have to extract keep-alives from incoming RTP streams, and
      MAY generate keep-alives on outgoing RTP streams.
   o  If the gateway detects or suspects loss of data on the RTP stream,
      and the lost data has not been retrieved using a redundancy
      mechanism, the gateway SHOULD insert the T.140 missing text marker
      [T140ad1] in the data sent on the outgoing T.140 data channel.
   o  If the gateway detects that the T.140 data channel has failed and
      got torn down, once the data channel has been reestablished the
      gateway SHOULD insert the T.140 missing text marker [T140ad1] in
      the data sent on the outgoing RTP stream if it detects or suspects
      that data sent by the remote T.140 data channel endpoint was lost.
   o  If the gateway detects that the T.140 data channel has failed and
      got torn down, once the data channel has been reestablished the
      gateway SHOULD insert the T.140 missing text marker [T140ad1] in
      the data sent on the outgoing T.140 data channel if it detects or
      suspects that data sent or to be sent on the T.140 data channel
      was lost during the failure.
   o  The gateway MUST indicate the same text transmission direction
      (Section 4.2.3) on the T.140 data channel and the RTP stream.

   NOTE: In order for the gateway to insert a missing text marker, or to
   perform other actions that require that the gateway has access to the
   T.140 data, the T.140 data cannot be encrypted end-to-end between the
   T.140 data channel endpoint and the RTP endpoint.  At the time of
   writing this document, no mechanism to provide such end-to-end
   encryption is defined.

7.  Update to RFC 8373

   This document updates RFC 8373 [RFC8373], by defining how the SDP
   hlang-send and hlang-recv attributes are used for the "application/
   webrtc-datachannel" media type.

Holmberg & Hellstrom    Expires October 12, 2020               [Page 13]
Internet-Draft             T.140 Data Channel                 April 2020

   SDP offerers and answerers MUST NOT include the attributes directly
   in the m= section associated with the 'application/webrtc-
   datachannel' media type.  Instead, the attributes MUST be associated
   with individual data channels, using the SDP 'dcsa' attribute.  A
   specification that defines a subprotocol that uses the attributes
   MUST specify the modality for that subprotocol, or how to retrieve
   the modality if the subprotocol supports multiple modalities.  The
   subprotocol is indicated using the SDP 'dcmap' attribute.

8.  Security Considerations

   The generic WebRTC security considerations are defined in
   [I-D.ietf-rtcweb-security-arch] and [I-D.ietf-rtcweb-security].

   The generic security considerations for WebRTC data channels are
   defined in [I-D.ietf-rtcweb-data-channel].  As data channels are
   always encrypted by design, the T.140 data channels will also be
   encrypted.

   The generic security considerations for the SDP-based external
   negotiation method are defined in
   [I-D.ietf-mmusic-data-channel-sdpneg].  There are no additional T.140
   data channel specific security considerations.

   When performing interworking between T.140 data channels and real-
   time text and the RTP based mechanism defined in [RFC4103], in order
   for a gateway to insert a missing text marker, or to perform other
   actions that require that the gateway has access to the T.140 data,
   the T.140 data cannot be encrypted end-to-end between the T.140 data
   channel endpoint and the RTP endpoint.

9.  IANA considerations

   [RFC EDITOR NOTE: Please replace all instances of RFCXXXX with the
   RFC number of this document.]

9.1.  Subprotocol Identifier t140

   This document adds the subprotocol identifier "t140" to the
   "WebSocket Subprotocol Name Registry" as follows:

         +--------------------------+----------------------------+
         | Subprotocol Identifier:  | t140                       |
         | Subprotocol Common Name: | ITU-T T.140 Real-Time Text |
         | Subprotocol Definition:  | RFCXXXX                    |
         | Reference:               | RFCXXXX                    |
         +--------------------------+----------------------------+

Holmberg & Hellstrom    Expires October 12, 2020               [Page 14]
Internet-Draft             T.140 Data Channel                 April 2020

9.2.  SDP fmtp Attribute

   This document defines the usage of the SDP 'fmtp' attribute, if this
   attribute is included in an SDP 'dcsa' attribute and associated with
   an T.140 real-time text session over a WebRTC data channel.  The
   usage is defined in Section 4.2.1.

   The usage level "dcsa(t140)" is added to the registration of the SDP
   'fmtp' attribute in the Session Description Protocol (SDP) Parameters
   registry as follows:

   +-----------------------+-------------------------------------------+
   | Contact name:         | IESG                                      |
   | Contact email:        | iesg@ietf.org                             |
   | Attribute name:       | fmtp                                      |
   | Usage level:          | dcsa(t140)                                |
   | Purpose:              | Indicate format parameters for a T.140    |
   |                       | data channel, such as maximum character   |
   |                       | transmission rates.                       |
   | Reference:            | RFCXXXX                                   |
   +-----------------------+-------------------------------------------+

9.3.  SDP Language Attributes

   This document modifies the usage of the SDP 'hlang-send' and 'hlang-
   recv' attributes, if these attributes are included in SDP 'dcsa'
   attributes associated with an T.140 data channel.  The modified usage
   is described in Section 4.2.2.

   The usage level "dcsa(t140)" is added to the registration of the SDP
   'hland-send' attribute in the Session Description Protocol (SDP)
   Parameters registry as follows:

   +-----------------------+-------------------------------------------+
   | Contact name:         | IESG                                      |
   | Contact email:        | iesg@ietf.org                             |
   | Attribute name:       | hlang-send                                |
   | Usage level:          | dcsa(t140)                                |
   | Purpose:              | Negotiate the language to be used on a    |
   |                       | T.140 data channel.                       |
   | Reference:            | RFCXXXX                                   |
   +-----------------------+-------------------------------------------+

   The usage level "dcsa(t140)" is added to the registration of the SDP
   'hland-recv' attribute in the Session Description Protocol (SDP)
   Parameters registry as follows:

Holmberg & Hellstrom    Expires October 12, 2020               [Page 15]
Internet-Draft             T.140 Data Channel                 April 2020

   +-----------------------+-------------------------------------------+
   | Contact name:         | IESG                                      |
   | Contact email:        | iesg@ietf.org                             |
   | Attribute name:       | hlang-recv                                |
   | Usage level:          | dcsa(t140)                                |
   | Purpose:              | Negotiate the language to be used on a    |
   |                       | T.140 data channel.                       |
   | Reference:            | RFCXXXX                                   |
   +-----------------------+-------------------------------------------+

9.4.  SDP Media Direction Attributes

   This document modifies the usage of the SDP 'sendonly', 'recvonly',
   'sendrecv' and 'inactive' attributes, if these attributes are
   included in SDP 'dcsa' attributes associated T.140 data channel.  The
   modified usage is described in Section 4.2.3.

   The usage level "dcsa(t140)" is added to the registration of the SDP
   'sendonly' attribute in the Session Description Protocol (SDP)
   Parameters registry as follows:

   +-----------------------+-------------------------------------------+
   | Contact name:         | IESG                                      |
   | Contact email:        | iesg@ietf.org                             |
   | Attribute name:       | sendonly                                  |
   | Usage level:          | dcsa(t140)                                |
   | Purpose:              | Negotiate the direction in which real-    |
   |                       | time text can be sent on a T.140 data     |
   |                       | channel.                                  |
   | Reference:            | RFCXXXX                                   |
   +-----------------------+-------------------------------------------+

   The usage level "dcsa(t140)" is added to the registration of the SDP
   'recvonly' attribute in the Session Description Protocol (SDP)
   Parameters registry as follows:

   +-----------------------+-------------------------------------------+
   | Contact name:         | IESG                                      |
   | Contact email:        | iesg@ietf.org                             |
   | Attribute name:       | recvonly                                  |
   | Usage level:          | dcsa(t140)                                |
   | Purpose:              | Negotiate the direction in which real-    |
   |                       | time text can be sent on a T.140 data     |
   |                       | channel.                                  |
   | Reference:            | RFCXXXX                                   |
   +-----------------------+-------------------------------------------+

Holmberg & Hellstrom    Expires October 12, 2020               [Page 16]
Internet-Draft             T.140 Data Channel                 April 2020

   The usage level "dcsa(t140)" is added to the registration of the SDP
   'sendrecv' attribute in the Session Description Protocol (SDP)
   Parameters registry as follows:

   +-----------------------+-------------------------------------------+
   | Contact name:         | IESG                                      |
   | Contact email:        | iesg@ietf.org                             |
   | Attribute name:       | sendrecv                                  |
   | Usage level:          | dcsa(t140)                                |
   | Purpose:              | Negotiate the direction in which real-    |
   |                       | time text can be sent on a T.140 data     |
   |                       | channel.                                  |
   | Reference:            | RFCXXXX                                   |
   +-----------------------+-------------------------------------------+

   The usage level "dcsa(t140)" is added to the registration of the SDP
   'inactive' attribute in the Session Description Protocol (SDP)
   Parameters registry as follows:

   +-----------------------+-------------------------------------------+
   | Contact name:         | IESG                                      |
   | Contact email:        | iesg@ietf.org                             |
   | Attribute name:       | inactive                                  |
   | Usage level:          | dcsa(t140)                                |
   | Purpose:              | Negotiate the direction in which real-    |
   |                       | time text can be sent on a T.140 data     |
   |                       | channel.                                  |
   | Reference:            | RFCXXXX                                   |
   +-----------------------+-------------------------------------------+

10.  Acknowledgements

   This document is based on an earlier Internet draft edited by Keith
   Drage, Juergen Stoetzer-Bradler and Albrecht Schwarz.

   Thomas Belling provided useful comments on the initial (pre-
   submission) version of the draft.  Paul Kyzivat and Bernard Aboba
   provided comments on the draft.

11.  References

11.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997, <https://www.rfc-
              editor.org/info/rfc2119>.

Holmberg & Hellstrom    Expires October 12, 2020               [Page 17]
Internet-Draft             T.140 Data Channel                 April 2020

   [RFC3264]  Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model
              with Session Description Protocol (SDP)", RFC 3264,
              DOI 10.17487/RFC3264, June 2002, <https://www.rfc-
              editor.org/info/rfc3264>.

   [RFC4103]  Hellstrom, G. and P. Jones, "RTP Payload for Text
              Conversation", RFC 4103, DOI 10.17487/RFC4103, June 2005,
              <https://www.rfc-editor.org/info/rfc4103>.

   [RFC4960]  Stewart, R., Ed., "Stream Control Transmission Protocol",
              RFC 4960, DOI 10.17487/RFC4960, September 2007,
              <https://www.rfc-editor.org/info/rfc4960>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8373]  Gellens, R., "Negotiating Human Language in Real-Time
              Communications", RFC 8373, DOI 10.17487/RFC8373, May 2018,
              <https://www.rfc-editor.org/info/rfc8373>.

   [I-D.ietf-mmusic-rfc4566bis]
              Begen, A., Kyzivat, P., Perkins, C., and M. Handley, "SDP:
              Session Description Protocol", draft-ietf-mmusic-
              rfc4566bis-37 (work in progress), August 2019.

   [I-D.ietf-rtcweb-data-channel]
              Jesup, R., Loreto, S., and M. Tuexen, "WebRTC Data
              Channels", draft-ietf-rtcweb-data-channel-13 (work in
              progress), January 2015.

   [I-D.ietf-mmusic-data-channel-sdpneg]
              Drage, K., Makaraju, M., Ejzak, R., Marcon, J., and R.
              Even, "SDP-based Data Channel Negotiation", draft-ietf-
              mmusic-data-channel-sdpneg-28 (work in progress), May
              2019.

   [I-D.ietf-rtcweb-security-arch]
              Rescorla, E., "WebRTC Security Architecture", draft-ietf-
              rtcweb-security-arch-20 (work in progress), July 2019.

   [I-D.ietf-rtcweb-security]
              Rescorla, E., "Security Considerations for WebRTC", draft-
              ietf-rtcweb-security-12 (work in progress), July 2019.

   [T140]     ITU-T, "Recommendation ITU-T T.140 (02/1998), Protocol for
              multimedia application text conversation", February 1998.

Holmberg & Hellstrom    Expires October 12, 2020               [Page 18]
Internet-Draft             T.140 Data Channel                 April 2020

   [T140ad1]  ITU-T, "Recommendation ITU-T.140 Addendum 1 - (02/2000),
              Protocol for multimedia application text conversation",
              February 2000.

11.2.  Informative References

   [RFC3261]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
              A., Peterson, J., Sparks, R., Handley, M., and E.
              Schooler, "SIP: Session Initiation Protocol", RFC 3261,
              DOI 10.17487/RFC3261, June 2002, <https://www.rfc-
              editor.org/info/rfc3261>.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550,
              July 2003, <https://www.rfc-editor.org/info/rfc3550>.

   [I-D.ietf-rtcweb-data-protocol]
              Jesup, R., Loreto, S., and M. Tuexen, "WebRTC Data Channel
              Establishment Protocol", draft-ietf-rtcweb-data-
              protocol-09 (work in progress), January 2015.

Authors' Addresses

   Christer Holmberg
   Ericsson
   Hirsalantie 11
   Jorvas  02420
   Finland

   Email: christer.holmberg@ericsson.com

   Gunnar Hellstrom
   Gunnar Hellstrom Accessible Communication
   Esplanaden 30
   Vendelso  136 70
   Sweden

   Email: gunnar.hellstrom@ghaccess.se

Holmberg & Hellstrom    Expires October 12, 2020               [Page 19]